background image

©Copyright Task Force Tips LLC 2004-2020

31

LIY-200 November 5, 2020 Rev19

8.4 REPAIR

Factory  service  is  available  with  repair  time  seldom  exceeding  one  day  in  our  facility.  Factory  serviced  equipment  is  repaired  by

experienced technicians, wet tested to original specifications, and promptly returned. Any returns should include a note as to the nature

of the problem and whom to reach in case of questions.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability for

damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.com for parts

lists, exploded views, test procedures and troubleshooting guides.  
Performance tests shall be conducted on the equipment after a repair, or anytime a problem is reported to verify operation in accordance

with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the equipment. Any

equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides are available with

each test procedure or equipment can be returned to the factory for service and testing. 

9.0 EXPLODED VIEWS AND PARTS LISTS

Exploded views and parts lists are available at tft.com/serial-number.

CAUTION

Any alterations to the product or its markings could diminish safety and constitutes a misuse of 

this product. 

NOTICE

All replacement parts must be obtained from the manufacturer to assure proper operation of the 

device. 

Summary of Contents for MONSOON Series

































Reviews: