background image

©Copyright Task Force Tips LLC  2020 

LIA-335 May 11, 2020 Rev00

TASK FORCE TIPS LLC

MADE IN USA • TFT.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

8.0 OPERATION AND INSPECTION CHECKLIST

BEFORE EACH USE

, equipment must be inspected to this checklist:

1. There is no obvious damage such as missing, broken or loose parts, damaged labels, etc.
2. Valve operates freely through full range and regulates 

fl

 ow

3. “OFF” position does fully shut o

  and 

fl

 ow is stopped 

4. The waterway is clear of obstructions
5.  Coupling is tight and leak free

BEFORE BEING PLACED BACK IN SERVICE

, equipment must be inspected to this list:

1. All controls and adjustments are operational
2. There are no broken or missing parts
3. Shuto

  valve closes o

  the 

fl

 ow completely

4. There is no damage that could impair safe operation (e.g. detents, cracks, corrosion, or other defects)
5. The waterway is clear of obstructions
6. The equipment is clean and markings are legible
7. Coupling is retightened properly

WARNING

Equipment failing any part of the checklist is unsafe for use and must have the problem corrected 
before use or being placed back into service. Operating equipment that has failed the checklist is 
a misuse of this equipment.

Summary of Contents for IN-LINE GAUGE WITH VALVE









Reviews: