Task Force Tips FlipTip Instruction For Operation And Maintenance Download

Page: 1 / 12

©Copyright Task Force Tips LLC 2012-2020

LIN-060 November 30, 2020 Rev02

TASK FORCE TIPS LLC

MADE IN USA · tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

G-Force

INSTRUCTION FOR OPERATION AND MAINTENANCE

FlipTip™ NOZZLE

WARNING

Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/serial-

number.
This equipment is intended for use by trained and qualified emergency services personnel for

firefighting. All personnel using this equipment shall have completed a course of education

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the

operation, servicing, and safety procedures associated with this product. This manual should be

kept available to all operating and maintenance personnel.

FlipTip Only

No Shutoff

FlipTip

Valve Shutoff

FlipTip

Valve Shutoff w/Pistol Grip

G-Force FlipTip

Valve Shutoff w/Pistol Grip

G-Force FlipTip

Valve Shutoff

Summary of Contents for FlipTip













Search results

Summary of Contents for FlipTip

Reviews:

Related manuals for FlipTip

Brands by name

Popular brands

Task Force Tips FlipTip, Instruction For Operation And Maintenance

Search results

Summary of Contents for FlipTip

Reviews:

Related manuals for FlipTip

Brands by name

Popular brands