background image

©Copyright Task Force Tips LLC   2014-2019 

LIA-208 August 12, 2019 Rev04

23

7.0 TROUBLE SHOOTING

SYMPTOM

POSSIBLE CAUSE

REMEDY

Leaks

Debris or damage in seal area

Clean  out  debris  or  replace  damaged 
parts

Binding, Erratic operation

Low Voltage (see below)

See Below

Power LED on but no operation

Low voltage due to:
    -wire gage too small
    -wire length too long
    -poor connection
    -inadequate apparatus electrical system

Check  connections  and  wiring  per 
section 4.3

LED  D6  on  motor  board  blinks 
rapidly when button is pressed

Loose encoder connection

Replace Motor Sub Assembly

Bad motor encoder     

Replace Motor Sub Assembly

No Power LED

Polarity reversed or poor connection

Check wiring and correct polarity

OPEN & CLOSE LED blink every 
4 seconds

No communication with Valve Motor

Check Blue & White communication 
wiring

8.0  TEN YEAR EXTENDED WARRANTY FOR JBIV-LP SERIES VALVES

Task Force Tips LLC, 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of its 
Low Profi le Ball Intake Valve (“equipment”), and to anyone to whom it is transferred, that the Low Profi le Jumbo Intake Valve series 
includes a 10 year warranty against manufacturing defects and corrosion aff ecting the valve’s operational performance.
TFT’s obligation under this warranty is specifi cally limited to replacing or repairing the equipment (or its parts) which are shown by 
TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the 
equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA, within a reasonable time after discovery of the 
defect. TFT will examine the equipment.  If TFT determines that there is a defect attributable to it, TFT will correct the problem within 
a reasonable time.  If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to 
refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited 
warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is 
an intended or unintended benefi ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental 
damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed 
and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to 
provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone 
else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL 
IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE. 
THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.
This limited warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.

Summary of Contents for Ball Intake Valve AXD1ST-NX-F





























Reviews: