Tascam DA-302, Owner'S Manual

Page: 28 / 33

29
Section 10 : Menu
…
E - - - - AH E - - - - AH
Shows the error rate during playback.
·
In the "----" section on the left, the error rate for Deck
1 is shown while in the "----" section on the right, that
for Deck 2 is shown.
·
The section showing AH can be changed with the
UP/DOWN key.
With AH display:
Shows the error rate of head A.
With AB display:
Shows the error rate of heads A and B.
With BH display:
Shows the error rate of head B.
·
Display example:
When "E0030AH E0100AH" is shown, the error rate
of head A in the PCM area is 3 x 10
-3 for Deck 1 and
1 x 10 -2 for Deck 2.
…
DrumT 1 (2)
Shows the elapsed drum rotating time since the deck
was first used. Use this as a guide for regular mainte-
nance.
…
Dig Out
Select the digital output signal format, SPDIF (IEC958
TYPE II) or AES/EBU (IEC958 TYPE 1), using the
UP/DOWN key.
…
Control
When using more than one DA-302, set them to mas-
ter/slave deck with the UP/DOWN key.
·
When only one DA-302 is used, set to "Master".
…
Copy ID
Set the Copy ID with the UP/DOWN key. The Copy ID
shows how many generations of digital-to-digital copy-
ing (digital recording of digital signals) is possible.
The Copy ID is recorded when recording is carried out.
Proh:
The copy prohibit ID (10) is recorded.
1gen:
The ID (11) permitting copy up to the first gener-
ation is recorded.
Free: The ID (00) permitting copy is recorded.
·
For digital-to-digital copying with an SCMS (Serial
Copy Management System) deck, see below.
When ID (10) is recorded:
A digital-to-digital copy is impossible.
When ID (11) is recorded:
One digital-to-digital copy is possible.
When ID (00) is recorded:
Multiple-generation digital-to-digital copying is
possible.
…
Peak Hold
Set the peak hold of the level meter to On or Off with
the UP/DOWN key.
·
When set to On, the peak is held. However, the held
peak level is reset if the MARGIN RESET key is
pressed.
…
Display
Select the brightness of the display with the UP/DOWN
key.
…
Seqtime
Sets the start time for Deck 2 operation during continu-
ous recording/playback with the UP/DOWN key. Can
be set in 1 minute increments (in 15 minute increments
with the
>
key) in the range of 0H15M00S to
2H30M00S.
When the ABS time of Deck 1 reaches the set time,
Deck 2 starts operation.
When more than one DA-302 is connected for continu-
ous recording/playback, and the ABS time of Deck 2
reaches the set time, the REC or PLAY command is out-
put from the EXT CONTROL OUT connector.
…
Cas Out
Select the signals output from the CASCADE OUT con-
nector with the UP/DOWN key.
When set to Input:
Signals input to the ANALOG IN connectors are out-
put to the ANALOG CASCADE OUTPUT connector.
Also, signals input to the DIGITAL INPUTS connec-
tor for Deck1 are output from the DIGITAL CAS-
CADE connector.
When set to Auto:
When either Deck 1 or Deck 2 plays back the tape, the
playback signal is output from the ANALOG CAS-
CADE OUTPUT and DIGITAL CASCADE OUT-
PUT connectors.
When both Decks 1 and 2 are playing back tapes, the
sound from the deck which entered the Play mode
most recently is output. To output the sound from
another deck, press the PLAY key of another deck in
the Play mode.
In other cases, the output signals are the same as that
output when set to Input.
…
Loop
Can be set only for the master deck.
When this is set to "On" with the UP/DOWN key, the
master deck starts operation again after the last slave
deck finishes the operation for continuous
recording/playback using more than one DA-302.
Menu Details