Tapeswitch PRSU/4 Operating Instructions Manual Download Page 9

 

© 

Copyright (2021) 

All

 rights reserved. Changes, which serve technical improvements are reserved.

 

 

PRSU/4, PRSU/5 Operating Instructions Manual (Revision 3.0) 

 
 
 

 
Fault Diagnostic and Subsequent Measures 
 

If the controller appears to be operating erroneously, please use the following  
diagnostic guide to determine what action should be taken.

 

 

 

 

Ground fault AC/DC 
(with electronic fuse 
protection)

 

If the input fuse blows and the output contacts open, safely locate the source 
of the fault and correct it, then replace the input fuse and follow the “Device 
Startup Verification” procedure on Page 4 of this manual. If normal operation 
of the device does not resume, retire the device and send to Tapeswitch  
Corporation for evaluation.

 

 

Faulty/welded 
Contact  
 

In the case of welded contacts, the device can no longer implement its  
intended function. Retire this device and send back to Tapeswitch  
Corporation for evaluation. 

 

Only one or no 
LED illuminates

 

In cases where either one or both “Channel” LEDs is OFF during normal  
operation, please verify that the device is properly wired. If the problem  
persists, the device is no longer capable of service. Retire the device and 
send to Tapeswitch Corporation for evaluation. 
 
 

 

Excessive contact-
to-contact resistance 

In cases where the device does not appear to operate properly, perform the 
following checks (cables removed from controller ports):  
 

1.  Upper (cables between S22 and S21) conductor plus total cable  

resistance in the unactuated state. Must be less than 10Ω. 
 

2.  Lower (cables between S11 and S12) conductor plus total cable 

resistance in the unactuated state. Must be less than 10Ω. 

 

3.  Upper to lower (cables going from S11 to S21) conductor plus total 

cable resistance. Measure at both sides (includes S21 to S22) during 
actuation

. Must be less than 200Ω. 

 
If the results exceed the stated limits, the system will need one or more  
additional controllers to conform to the maximum resistance parameters per 
relay. 
 
If the results are within the allowable limits and the controller is still not  
working, contact Tapeswitch as the unit is likely faulty. 
 

 

 
 

 

Summary of Contents for PRSU/4











Reviews: