Tao Motor TBR7 Owner'S Manual Download Page 30 | Manualshive

Page: 30 / 47

background image

1. Side Stand Spring

SIDE STAND

If the side stand is stiff or squeaky, clean the pivot area and

lubricate the pivot bolt with clean engine oil.

1. Check the side stand spring (1 ) for damage and loss of tension.

2. Check the side stand assembly for freedom of movement.

①

Worn Sprocket

Teeth

Damaged Sprocket

Teeth

REPLACE

Normal Sprocket Teeth

GOOD

REPLACE

NOTICE: Use of a new chain with worn sprockets

will cause chain wear

.

Inspect the front and rear sprocket teeth for excessive wear

or damage. If necessary, have your Tao Motor dealer replace

a worn sprocket.

Sprocket

26

«
...
28
29
30
31
32
...
»

Summary of Contents for TBR7
















































Reviews:

No comments

Related manuals for TBR7

Brand: Baotian Pages: 30

X-903 Ultra Carbon 29

Brand: X-lite Pages: 116

Brand: R&G Pages: 2

Brand: R&G Pages: 26

Brand: Honda Pages: 130

Brand: Big Bike Parts Pages: 3

Brand: Thunderbike Pages: 7

STAR XV19CSX(C)

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 100

Star XV250B 2011

Brand: Yamaha Pages: 98

Brand: Dynafit Pages: 20

Brand: Yamaha Pages: 9

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 91

Brand: Yamaha Pages: 92

Virago XV250 2004

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands