background image

Fig. T 

Fig. U 

7

. Remove the screw (Fig. U) from the side reflector and lift it up away from the heater to remove it. Repeat at 

opposite end to remove other side reflector. 
 
 

8

.  The  lamp  emitter  wires  should  be  pulled  out  of  the  side  slots  and  the  lamp  emitter  can  be  lifted  up        

completely (Fig. V). The wires should be gently pulled so they come out from behind the reflector. 

9

. The lamp emitter should now be removed from the heater as shown in Fig. X. 

 
 

10

.  Refit  the  new  lamp  emitter  in  reverse  order  ensuring  that  no  wires  get  trapped  and  all  screws  are  fully         

tightened.

 

Fig. X 

Fig. V 

10 

Keep the mains supply cord away from the body of the heater which will 
get hot during use. 

 

Arrange the mains supply cord so it cannot be tripped over or damaged. 

 

Do not cover or obstruct the heater while it is in use. 

 

Do not insert any object through any slot or opening in the heater. 

 

Do not use if a guard is not present. 

 

Do not install less than the minimum mounting distance from the floor. 

 

WARNING: 

This heater should only be installed with an energy saving 

device to control the room temperature and operated by users capable 
of  using  the  device.  Do  not  use  this  heater  in  small  rooms  when  they 
are occupied by persons not capable of leaving the room on their own, 
unless constant supervision is provided. 

 

Do not touch the heater when it is turned on, as the body gets hot. 

 

Do  not  use  the  heater  in  a  bathroom,  laundry  areas  and  similar        
locations. Never locate the heater where it may  fall  into  a  bathtub  or 
other water container. 

 

A heater has hot parts inside. Do not use it in areas where petrol, paint, 
or flammable liquids are used or stored. 

 

If  the  supply  cord  becomes  damaged,  it  must  be  replaced  by  the     
manufacturer, its service agent or a similar qualified person in  order to 
avoid a hazard. 

 

WARNING

:  This  appliance  must  be  connected  to  a  supply  that  is 

earthed!

 

 
I M P O R TA N T   -  
S AV E   T H E S E   I N S T R U C T I O N S   F O R   F U T U R E   R E F E R E N C E  

 

 Keep combustible material such as furniture, papers, 
 clothes and curtains at least 1.8m (6ft) away from the 
 sides and rear.

 

W A R N I N G :   R I S K   O F   F I R E

W A R N I N G :   R I S K   O F   F I R E

W A R N I N G :   R I S K   O F   F I R E

W A R N I N G :   R I S K   O F   F I R E  

1.8m 

(6ft) 

Summary of Contents for Sorrento IP Triple







Reviews: