Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: [email protected]
E: [email protected]
E: [email protected]
E: [email protected]
POWERV12
Tannoy adopts a policy of continuous improvement and product specification is subject to change
POWERV12 data file // Issue: 1.06 // 15.01.08
TECHNICAL SPECIFICATIONS
System Type
Full Range - Vented
Frequency Response (-3dB)
(1)
70Hz - 25kHz
Full Range Mode
Frequency Range (-10dB)
(1)
55Hz - 38kHz
Full Range Mode
Frequency Response (-3dB)
(1)
100Hz - 30kHz
High Pass Mode
Frequency Range (-10dB)
(1)
80Hz - 38kHz
High Pass Mode
Dispersion (-6dB)
90 degrees conical
Driver Complement
1 x 300mm (12.00”)
Dual Concentric™
Crossover
Passive 1.4kHz
Directivity Factor (Q)
8.2 averaged 1kHz to 10kHz
Directivity Index (DI)
8.8 averaged 1kHz to 10kHz
Rated Maximum SPL
(2)
Average
120dB
Peak
126dB
Distortion
10% Full Power (
8.9V
)
2nd Harmonic
3rd Harmonic
250Hz
0.56%
0.23%
1kHz
2.36%
1.88%
10kHz
2.68%
0.08%
1% Full Power (
2.8V
)
2nd Harmonic
3rd Harmonic
250Hz
0.14%
0.14%
1kHz
0.38%
0.94%
10kHz
1.03%
0.05%
Crossover
1.4kHz Passive
PSU Specifications
Input Connector
Locking Neutrik Powercon
Voltage Selection
Automatic (115 / 230V, 45 - 65Hz)
Switching Frequency
192kHz Syncronised to DSP
Type
High current, high freq. switch-mode
Efficiency
>90% typical
Input voltage
100v / 115v / 230v n/-10%
Mains fuse
External
Fuse type
T10AT
Other features
Automatic soft start
Enclosure
37.5 litre vented and internally braced
15mm (0.62”) birch plywood enclosure
15mm (0.62”) MDF front baffle
Finish
Textured black or white paint with
custom colours on request
Powder coated steel grille with
reticulated foam behind
Connectors
1 x female XLR (input)
1 male XLR (link)
1 x Neutrik Powercon
Controls &
Level control
Indicators
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full range / High pass switch (110Hz)
Power switch
Fittings
8 x M10 inserts for flying hardware
8 x M10 yoke bracket inserts
3 x recessed carrying handles (2 side &
1 rear)
Blanking plate for optional VTH pole
mount
Dimensions
486 x 370 x 260mm
(H x W x D)
19.13 x 14.57 x 14.17”
NET Weight
23kg
50.6lbs
Electronics
Maximum signal input for clip
Input attenuator at minimum: +18dBu
Input attenuator at maximum: +5dBu
Output noise
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
Efficiency
>90% typically
Damping Factor
400 ref 8 Ohms
Distortion
<0.05% @ 1kHz -3dB output
(22kHz bandwidth)
Input Impedance
5.6k Ohms unbalanced
11.2k Ohms balanced
Protection systems Over current Excessive over current causes shutdown
Temperature Limiters applied
Brownout
Automatic protection & recovery
Mains
Inrush current limiting
Indicators
1x Limit LED
1x Signal LED
1x Power LED
Number of channels
One
System Type
Class D
System
POWERV12
Construction
8001 4270
POWERV12
Black
1
8001 4271
POWERV12
White
1
PART NUMBER
PACKED QUANTITY
COLOUR
MODEL NAME
Ordering Information
NotesNotes:
(1) Average over stated bandwidth. Measured at 1 metre on axis.
(2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
