background image

8

CENTRE CHANNEL SPEAKER

(See figs. 3 and 4)

The Eyris centre channel speaker is fully magnetically shielded and designed for installation
directly above or below the TV. As the main effects speaker for the front soundstage, the
critical factor in its performance is the placement.  In all cases the centre channel speaker
should be positioned as near to the TV screen as possible. The viewing position when
seated determines the ideal mounting height, but in all cases this should be as close as
possible to ear height. As with the main speakers the front baffle panel should be as near
as possible in line with the screen surface.
The Eyris centre channel can be wired in single wire or bi-wire mode, 

(see figs. 3 and 4)

,

bear in mind that connection should be made to the dedicated centre channel output on
your A/V processor amplifier.

REAR EFFECTS SPEAKERS

The integrity of the special effects soundstage created by the source material will be
compromised if the speakers are installed on the sidewalls, for that reason they should
always be placed behind the main viewing position.
The placement of floor standing speakers at the rear should mirror as near as possible
the location of the front pair and 0.5 metres (20 inches) from the rear wall. Wall-mounted
loudspeakers should be shelf or bracket mounted 1.5 to 4.5 metres (5ft to 15ft) apart with
a height mounting height range of 1.5 to 2 metres (5ft to 7ft).

SUBWOOFER

As the subwoofer only produces low frequency, therefore monaural information, it is difficult
to detect its location by ear. It could as a result be situated anywhere in the room, but
optimum performance will be gained by locating the subwoofer between the main stereo
pair of speakers. Bass output will increase when placed next to a wall or in a corner so
use the subwoofer volume control to balance the output with the rest of the system.
Please refer to the manual supplied with the subwoofer for advice on installation and set-up.

CABINET

Enclosure type

Reflex

Dual chamber coupled reflex Dual chamber coupled reflex Twin Reflex

Closed Box

Construction

Dimensions - inc grille mm (inches)

360 x 170 x 259

908 x 170 x 259

1023 x 196 x 259

205 x 430 x 259

235 x 280 x 169

(14.2 x 6.7 x 10.2)

(35.7 x 6.7 x 10.2)

(40.3 x 7.7 x 10.2)

(8.1 x 16.9 x 10.2)

(9.3 x 11 x 6.6)

Volume - litres

7.5

21

29

11

3.8

Weight kgs (lbs)

7 (15.4)

16 (35.3)

18.5 (40.8)

13 (28.6)

5.5 (12.1)

Finish options

18mm MDF, internally

cross-braced enclosure

30mm front baffle

18mm MDF, internally

cross-braced enclosure

30mm front baffle

18mm MDF, internally

cross-braced enclosure

30mm front baffle

18mm MDF, internally

cross-braced enclosure

30mm front baffle

18mm MDF, internally

cross-braced enclosure

30mm front baffle

Sycamore

American Walnut

Sycamore

American Walnut

Sycamore

American Walnut

Sycamore

American Walnut

Sycamore

American Walnut

25-micron titanium

dome, neodymium

magnet system

Multi fibre paper

pulp cone

CROSSOVER

Frequency

2.2kHz

200Hz - 2.2kHz

200Hz - 2.2kHz

2.2kHz

2.2kHz

Type

2nd order LF

1st order HF

2nd order LF

1st order HF

2nd order LF

1st order HF

2nd order LF

1st order HF

25-micron titanium

dome, neodymium

magnet system

25-micron titanium

dome, neodymium

magnet system

25-micron titanium

dome, neodymium

magnet system

25-micron titanium

dome, neodymium

magnet system

Multi fibre paper

pulp cone

Multi fibre paper

pulp cone

Multi fibre paper

pulp cone

Multi fibre paper

pulp cone

2nd order LF

1st order HF

EYRIS 1

EYRIS 2

EYRIS 3

EYRIS CENTRE

EYRIS REAR

PERFORMANCE

Recommended amplifier power - Watts RMS 20 - 75

20 - 125

20 - 150

20 - 125

20 - 75

Continuous power handling - Watts RMS

55

95

110

100

55

Peak power handling - Watts

180

290

360

290

180

Sensitivity (2.83Volts @ 1 mtr)

87dB

87.5dB

88dB

89dB

87dB

Nominal impedance - Ohms

8

8

8

8

8

Frequency response - 6dB

48Hz - 44kHz

42Hz - 44kHz

38Hz - 44kHz

52Hz - 44kHz

55Hz - 44kHz

DRIVE UNITS

WideBand™ high frequency

25mm (1")

25mm (1")

25mm (1")

25mm (1")

25mm (1”)

Low frequency

145mm (6")

2 x 145mm (6")

2 x 175mm (7")

2 x 145mm (6")

145mm (6")

TECHNICAL SPECIFICATIONS

T R A N S L AT E D   . P D F   D O W N L O A D S   O F   T H I S   M A N U A L   A R E   A V A I L A B L E   O N   O U R   W E B S I T E   AT

w w w. t a n n o y. c o m

Summary of Contents for EYRIS













Reviews: