TANKLESS 000 Btu/hr Use And Care Manual Download

Page: 59 / 72

Remote Control Installation (cont.)

Connecting the Remote Control to the Water Heater:

Ensure that the power to the water heater has been

disconnected.

Loosen the one screw located on the remote control

connection cover. The connection cover is made of

white plastic.

NOTICE:

DO NOT REMOVE FRONT PANEL.

Remote control wires are connected on the bottom of

the unit.

There are no accessible remote control terminals

inside the water heater.

Connect the remote control extension cables from

the remote control to the remote control connection

terminals.

NOTICE:

The remote control wire connection

terminals are not polarity-sensitive.

Firmly tighten the terminal screws by hand.

Secure the remote control extension cable on the hook

located on the side of the remote control connection

base.

Reinstall the remote control connection cover and

secure with the one screw.

Switch on the power supply to the water heater.

Check for proper operation of the remote control and

the water heater.

Remote Control

Connection Cover

Electrical Wiring (cont.)

INSTALLATION INSTRUCTIONS

Electrical

Summary of Contents for 000 Btu/hr









































































Search results

Summary of Contents for 000 Btu/hr

Reviews:

Related manuals for 000 Btu/hr

Brands by name

Popular brands

TANKLESS 000 Btu/hr, Use And Care Manual

Search results

Summary of Contents for 000 Btu/hr

Reviews:

Related manuals for 000 Btu/hr

Brands by name

Popular brands