TANKLESS 000 Btu/hr Use And Care Manual Download

Page: 30 / 72

INSTALLATION INSTRUCTIONS

• Visually inspect the water heater for any possible

damage.

• Check the rating plate on the water heater to make

sure the water heater was designed to be used with the

supplied type of gas (natural or LP).

• Verify that all included supplied parts are present as

shown.

(Some models only)

General

Product Inspection

Water Heater Installation

Corrosive Atmosphere

NOTICE:

The water heater should not be installed

near an air supply containing halogenated hydrocarbons.
Avoid installing a water heater in any of the following

locations: beauty shops, dry-cleaning establishments,

photo processing labs, and storage areas for liquid and

powdered bleaches or swimming pool chemicals. These

locations often contain such halogenated hydrocarbons.

The air supply containing halogenated hydrocarbons is

safe to breathe, but when passed through a gas flame,

corrosive elements are released that will shorten the life

of any gas-burning appliance.
Propellants from common spray cans or gas leaks from

A/C and refrigeration equipment are highly corrosive after

passing through a flame.
The water heater warranty is void when the failure is due

to operation in corrosive conditions.

Remote Control Cable

Remote Control

Manual Gas Shut-Off Valve

Screws

Washers

Pressure Relief Valve

Summary of Contents for 000 Btu/hr









































































Search results

Summary of Contents for 000 Btu/hr

Reviews:

Related manuals for 000 Btu/hr

Brands by name

Popular brands

TANKLESS 000 Btu/hr, Use And Care Manual

Search results

Summary of Contents for 000 Btu/hr

Reviews:

Related manuals for 000 Btu/hr

Brands by name

Popular brands