Tanda TX7210 Installation And Operation Manual Download Page 2

                                                                                                       TX7210 Addressable Single Input/Output Module 

 

 

        Installation & Operation Manual  

                                                                                                                                4050100267-Rev1.6-0916                                                                      

 

 

    TANDA UK  

                                                                                                                                           

Specifications are subject to change without prior notice 

     

 

 
 
Product Safety 
 
 
To prevent severe injury and loss of life or property, read the instruction carefully before installing the 
module to ensure proper and safe operation of the system.  
 
 
 
 

 

European Union directive 

2012/19/EU (WEEE directive): 

Products marked with this symbol cannot be disposed 

of as unsorted municipal waste in the European Union. For proper recycling, return 
this  product  to  your  local  supplier  upon  the  purchase  of  equivalent  new 
equipment, or dispose of it at designated collection points.

  

 
For more information please visit the website at 

www.recyclethis.info

 

 

 
 
 
EN54 Part 18 Compliance 
 
TX7210 Addressable Single Input/output Module complies with the requirements of EN 54-18:2005. 
 

EN54 Standard Conformity Information  
  

 

0832 

17

 

TANDA(UK) LIMTIED 
FOURTH FLOOR 30-31 FURNIVAL STREET LONDON EC4A 
1JQ(Type 1, Option 2 Crosslisting) 
 
TX7210  0832-CPR-F1830  

EN 54-18:2005   

 
 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TX7210












Reviews: