background image

6

SPECIFICATIONS

Model

TCS33ED (35S)

TCS33ED (40S)

Type of equipment

Chain saw, portable

Engine Size (cm

3

)

32.2

Spark Plug

NGK BPMR-7A

Fuel Tank Capacity (cm

3

)

290

Chain Oil Tank Capacity (cm

3

)

180

Dry Weight (kg)  

(Without guide bar and chain)

3.7

Guide bar length (mm)

350

400

Chain pitch (mm)

9.53

Chain gauge (mm)

1.27

Sound pressure level LpA (dB (A)) by ISO 22868

 Equivalent 

*

1

 Uncertainty

100

1

Sound power level LwA (dB (A)) by ISO 22868

 Measured 

*

2

 Uncertainty

Sound power level LwA (dB (A)) by 2000/14/EC

 Measured 

*

2

 Guaranteed

112

1.5

112

114

Vibration level (m/s

2

) by ISO 22867

 

Front handle *

1

 

Rear handle *

1

 Uncertainty

3.8

4.6

1

Max. engine power 

by ISO 7293 (kW)

1.3

Max. engine speed (min

-1

)

13500

Idle engine speed (min

-1

)

2800 – 3200

Type of chain

91PX

(Oregon)

Max. chain speed (m/sec)

25.7

Sprocket (number of teeth)

6

Type of drive sprocket

Spur

NOTE:  

Noise level/vibration levels are calculated as the time-weighted energy total for noise/vibration levels under various working 

conditions with the following time distribution: 

 

*

1

: 1/3 idle, 1/3 full, 1/3 racing speed.

 

*

2

: 1/2 full, 1/2 racing speed.

 

All data subject to change without notice.

000Book̲TCS33ED̲Eng.indb   6

000Book̲TCS33ED̲Eng.indb   6

2017/12/18   10:26:31

2017/12/18   10:26:31

Summary of Contents for TCS 33ED





















Reviews: