background image

FUEL

Use regular grade unleaded gasoline mixed with 2-cycle
engine oil in 25:1 ratio for best results. Use   mixing ratios
in Section 

FUEL MIXING TABLE.

MIXING FUEL

Mix fuel with Talon brand 2 cycle oil in an approved   con-
tainer. Use mixing table for correct ratio of fuel to oil.
Shake container to ensure thorough mix.

FUEL AND LUBRICATION

FUEL MIXING TABLE

RECOMMENDED FUELS

Some conventional gasolines are being blended with oxy-
genates such as alcohol or an ether compound to meet
clean air standards. Your Talon engine is designed to
operate satisfactorily on any gasoline intended for auto-
motive use including oxygenated gasolines.

STARTING A COLD ENGINE

Fill fuel tank with proper gas and oil mixture. See Fuel and
Lubrication. Set unit on ground so that it rests on housing

feet.
1. Pull the trhottle trigger (A). (It will auto lock) Fig. 4A.
2. Prime the carburetor. Pump the primer bulb (C) 10

times (Fig. 4B).

3. Your unit is designed with a 2 position choke (D):

START “ ” and RUN “ ”. Move choke lever to
START “ ” position (Fig. 4C).

4. Grip handle firmly .
5. Pull starter rope out a short way until resistance is felt

(approximately 100mm). Pull starter rope until engine
starts or attempts to run.Once engine starts, warm up
at full throttle for 10 seconds and release throttle.

6. Push down the throttle lock (B), the throttle trigger (A)

will back to the nomal position. (Fig. 4A)

7. Move the choke to RUN “ ” position (Fig. 4E).

NOTE: 

If engine fails to start after repeated attempts, refer

to Troubleshooting section.

NOTE:

Always pull starter rope straight out. Pulling starter

at an angle will cause rope to rub against the eyelet. This
friction will cause the rope to fray and wear more quickly.
Always hold starter handle when rope retracts. Never
allow rope to snap back from extended position. This
could cause rope to snag or fray and also damage the

starter assembly.

• STOPPING THE ENGINE
Emergency Stopping Procedure

. When it is necessary

to stop blower engine immediately, DEPRESS the switch
to stop.

Normal Stopping Method.

For normal stopping, push

down the throttle lock, the throttle trigger will back to the
nomal position and allow engine to return to idle speed.
Then DEPRESS and HOLD the “OFF” switch until the
engine stops completely.

• STARTING A WARM ENGINE 

(Engine has been

stopped for no more than 15-20 minutes)

1. Pull starter rope again. Engine should start with ONE or

TWO pulls. If engine fails to start after 6 pulls, repeat
steps 2 through 6 .

2. If engine does not start, or starts and then stops after 5

rope pulls, follow procedure “STARTING A COLD
ENGINE”.

FUEL AND LUBRICATION

WARNING

: Never use straight gasoline in your

unit. This will cause permanent engine damage

and void the manufacturer’s warranty for that

product. Never use a fuel mixture that has been

stored for over 90 days.

WARNING

: If 2-cycle lubricant other than Talon

Custom Lubricant is to be used, it must be a  pre-

mium grade oil for 2-cycle air cooled engines

mixed at a 40:1 ratio. Do not use any 2-cycle oil

product with a recommended   mixing ratio of

100:1. If insufficient lubrication is the cause of

engine damage, it voids the manufacturer’s

engine warranty for that occurrence.

WARNING

: Lack of lubrication voids engine

warranty.

Gasoline and oil

mix 25:1

GASOLINE

25:1 Ratio Lubricant

5 Liters 

6.7 oz.

200ml (cc)

1 lmp. Gal.

6.1 oz.

180ml (cc)

Mixing 

25 Parts Gasoline

Procedure

to 1 part Lubricant

1ml = 1cc

3

2

GB

GB

1. Rear Handle

2. Throttle Trigger

3. Throttle Lock

4. On/Off Switch

5. Front Handle

6. Muffler Cover

7. Fuel Tank Window

8. Fuel Cap

9. Starter Handle

10. Air Filter Cover

11. Vacuum/Blower Tube

12. Choke Lever

13. Spark Plug Wire /

Spark Plug

14. Vauum/Blower Slide

15. Primer Bulb

16. Harness

17. Vacuum Bag

18. Speed Cleaner head

(Model  AB320325

only)

1

GENERAL IDENTIFICATION

2

3

4

5

6

7

8

9

10

13

15

11

12

16

14

• 

BLOWER ATTACHMENT ASSEMBLY INSTRUC-

TIONS

1. Release the screws (A ) and insert blower tube (B) into

the  blower housing and tight the screws (B). (Fig. 1A)

2. Insert speed cleaner head (C) to the tube (B). (Fig. 1B

Model AB320325 only)

• 

HARNESS INSTALLATION 

Attach the 2 harness clips to the 2

links in the blower handle. (Fig. 2)

•  VACUUM ATTACHMENT

ASSEMBLY INSTRUCTIONS

To install vacuum bag:

ASSEMBLY INSTRUCTIONS

Fig. 3

B

A

17

18

Fig. 2

Fig. 1A

Fig. 1B

A

B

B

C

OPERATING INSTRUCTIONS

Fig. 4D

Fig. 4E

Fig. 4A

C

A

Fig. 4B

Fig. 4C

D

D

B

Reviews: