Talkaphone AOR-16 Installation Instructions Manual Download Page 4 | Manualshive

Page: 4 / 39

background image

Area of Rescue Command Unit

Installation Instructions

Model AOR-8 / Model AOR-16

Page

3

of

12

Rev. 8/18/2016

Copyright 2016 Talk-A-Phone Co.

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.

All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.

4.

Carefully open the hinged front cover taking care there are no loose items
which may have shifted during transportation.

5.

The AOR-8 or AOR-16 may be either surface mounted onto a wall or flush
mounted into a wall.

NOTE:

For flush mounting units, AOR-8 and AOR-16 units should be

ordered with the available AOR-TR16 Flush Mount Trim Ring (sold
separately).

NOTE:

Conduit knockouts exist on the rear, top, and bottom sides of the

enclosure for access to power and communication lines. Determine the
method of bringing in these power and communication lines

before

mounting the enclosure.

NOTE:

Whenever possible, it is best to keep the maximum clearance

possible between analog phone lines and alternating current. Running
phone lines too close to hot VAC lines will produce undesired effects on
the phone line.

6.

For mounting the unit directly to the surface of an interior wall,
The AOR-8 and AOR-16 has six (4) surface mounting keyholes.

7.

For Flush Mounting the Unit

The AOR-8 and AOR-16 each have eight (8) 7/32 [in] knockouts located on the
top, bottom and sides which can be used for either mounting the unit within a
wall or to fasten the available AOR-TR16 Flush Mount Trim Ring. This trim ring
may be installed in contact with the closed cover without inhibiting the
functionality of the hinge.

8.

Secure the AOR-TR16 to the AOR-8 or AOR-16 unit in the desired location
using the provided 6-32 screws, two (2) washers, and hex nut

9.

Installation of Strobe/Siren
Mount the strobe/siren assembly on a wall in an appropriate location per the
instructions packaged with the strobe/siren assembly.

10.

Three (3) outgoing low voltage power lines from the strobe/siren assembly must
be wired to the Black, Red/White, and Orange lead wires from the relays

«
...
2
3
4
5
6
...
»

Summary of Contents for AOR-16








































Reviews:

No comments

Related manuals for AOR-16

Brand: Xorcom Pages: 2

Brand: Hanlong Pages: 60

Brand: AEI COMMUNICATIONS Pages: 5

Brand: ShoreTel Pages: 2

Brand: UNITe IP Pages: 116

Brand: Beacon Pages: 2

STRATA CTX DKT3014-SDL

Brand: Toshiba Pages: 2

Strata IP5000 series

Brand: Toshiba Pages: 12

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 5

Strata CIX IP5000-Series

Brand: Toshiba Pages: 12

Brand: Toshiba Pages: 37

Brand: Toshiba Pages: 57

Strata CT 2000 Series

Brand: Toshiba Pages: 196

Strata CIX IP5000 Series

Brand: Toshiba Pages: 216

Brand: Toshiba Pages: 378

Brand: Aastra Pages: 40

Brand: Aastra Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands