background image

 

Area of Rescue Command Unit

 

Installation Guide 

Model AOR-5 / Model AOR-10

 

Page 

5

 of 

23

 

 

  Rev. 4/13/2022

 

 

Copyright 2022 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.  

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, bAlert, Scream Alert, WEBS, and WEBS Contact are registered trademarks of 
Talk-A-Phone, LLC.  All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate 
any approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

 

 

Figure 3.  

Model AOR-10

, front view. 

 

Figure 4.  

Model AOR-10

, internal components.

 

Item 

Component 

Local Handset 

PSTN Line Disconnect 
Button 

Station Selection Buttons 

Sub-Command Unit 
Selection Buttons 

Status LEDs 

Fault LEDs 

FAULT RESET 

Key Switch 

Item 

Component 

10-channel Controller Board 

Station 1-10 Terminals 

“TELCO IN” 

Terminal 

Open/Short/System Ground 
Fault/AOR-CSE Station 
Activation Relay Outputs 

24VDC Input Terminal 

Orange-red Configuration 
Button 

4.5Ah Backup Battery 

Summary of Contents for AOR-10
























Reviews: