manualshive.com logo in svg

Talex PROFI CLEAN 2800, User Manual, Page: 32 / 39

Share
Download
Talex PROFI CLEAN 2800 User Manual Download Page 32

Talex Spółka z ograniczoną 

odpowiedzialnością

 

Spółka komandytowa 

ul. Dworcowa 9c     , 77-141 Borzytuchom 

tel. 

(59) 821 13 40 

e-mail

 

[email protected]

 

www.talex-sj.pl

 

 

Page 

32

 of 

32

 

 

 

Attention:

 

 Lubricate the bearing pin before assembly. 

 Make sure that the roller brush does not twist during assembly. 

 

8.2 Assembly and replacement of the side brush  

 
 
In order to remove the side brush, remove the M10x40 screw and then unscrew 3 M10 nuts. 
Remove the worn brush and replace it with a new one, then tighten the nuts and the screw 
again. 
 

 

 
 
 
 
 
 
 
 

      Photo 21. 

 

 

 
 
 
 

Table 7.

 TIGHTENING TORQUE VALUES FOR BOLTS AND NUTS 

 

Durability 

6.8 

8.8 

10.9 

12.9 

Metric thread 

Tightening torque [Nm] 

M5 

4.5 

5.9 

8.7 

10 

M6 

7.6 

10 

15 

18 

M8 

18 

25 

36 

43 

M10 

37 

49 

72 

84 

M12 

64 

85 

125 

145 

M14 

100 

135 

200 

235 

M16 

160 

210 

310 

365 

M18 

220 

300 

430 

500 

M20 

310 

425 

610 

710 

M22 

425 

580 

820 

960 

M24 

535 

730 

1050 

1220 

Summary of Contents for PROFI CLEAN 2800








































Reviews:

No comments