TALAMEX QLS200 User Manual Download Page 5

Talamex inflatable boats – User’s manual 

Pagina 5 van 17 

 

2.3 

Number of persons 

warning 

Do not exceed the maximum recommended number 

of persons. Regardless of the number of persons 

aboard, the total weight of persons and equipment 

must never exceed the maximum recommended 

load. 

 

2.4 

Payload 

warning 

When loading the Talamex inflatable boat, never 

exceed the maximum recommended load. Always 

load the Talamex inflatable boat carefully and 

distribute loads appropriately to maintain design 

trim (approximate level). Avoid placing heavy 

weight high up. 

 

2.5 

Outboard Engine 

The maximum motor power of this boat is given in 
2.9 in this manual. 

danger 

Overpowering a boat can result in serious injury, 

death or boat damage. 

 

danger 

You might lose control of the boat when using the 

motor at full speed, accidents may occur. 

Talamex cannot be held responsible for these 

actions. 

 
 

warning 

Be cautious when refuelling, e.g., no smoking and 

direct treatment of fuel spillage in craft. 

Prevent the fuel lines from damaging when installing 

the engine. 

Avoid and prevent contact of flammable materials 

with hot engine parts. 

 

2.6 

Fire extinguisher 

warning 

In case you have a boat with outboard engine 

having more than 25kW (34HP). Then you are 

required by NEN-EN ISO 9094-1 to have one or 

more fire extinguishers on board with a collective 

capacity of 8A/68B. 

Ask your dealer for supply of a fire extinguisher 

that is conform the requirements. 

 

2.7 

Electrical system 

 

let op 

Your Talamex boat comes standard without 

electrical system and connections. If you install an 

electrical system, it must meet the following 

international standards for water resistance: ISO 

10133, ISO 9097 of ISO 8849. Navigation lights 

must comply with Colreg 72. 

Ask your dealer for supply of a system that is 

confirm the requirements. 

 

2.8  

Certification 

 
All boats from 250cm and up are CE certified by the 
Notified Body DMI (NoBo nr. 2248) or EMCI 
(NoBo nr. 2832).

 

 

Summary of Contents for QLS200


















Reviews: