background image

 

 

About these Operating Instructions 

Operating instructions 

 

 
 

Version 1.0.0 

Rotary indexer RTX 

Page 3 of 35    

1

 

 About these Operating Instructions 

These Operating Instructions describe the partly completed machinery Rotary indexer.  
The Rotary indexer is referred to below as the partly completed machinery. 
 
The Operating Instructions are intended to help you to: 

 

work efficiently 

 

ensure quality 

 

find information quickly 

 

avoid danger 

 
Table of contents 
The Operating Instructions have a table of contents at the front. This gives you an overview of all the sections in the 
document. 
 
Headings and page numbers 
The chapters are numbered sequentially. The sections within each chapter are numbered sequentially. 
 
Safety information 
Any safety information is placed before the descriptions of actions that may pose a risk. You will find a detailed 
description of the safety information in the chapter entitled Safety. 
 
Text, symbols, figures 
Instructions for performing various activities and other information are presented in small, discrete sections. 
The information is presented using a combination of text, symbols and figures. 
Instructions for performing action are described in the appropriate sequence and numbered accordingly. 
 
Instructions for action 
For the sake of clarity the instructions for action have been broken down into individual steps: 

 

Introductory text…

 

 

Instruction result 

 
Lists 
Any lists which do not include individual operating steps are indicated as follows: 

 

Lists…

 

o

 

Sub-items in lists 

 
Figures 
Figures, dimensions and technical data presented in these Operating Instructions may be subject to change. 
 
Cross-references 
Cross-references point you to additional descriptions within the Operating Instructions. (Chapter number/page 
number). 
 
Third-party components 
Refer to the Operating Instructions of the relevant manufacturers for information on operation and maintenance of 
third-party components fitted in the system. 
 
Additional documentation 
To complement the information in these Operating Instructions, please read the following regulations and directives: 

 

safety regulations and accident prevention regulations 

 

instruction sheets, instruction booklets 

 

work instructions provided by the statutory accident insurance provider 

 

generally accepted occupational health regulations 

 

 

Summary of Contents for RTX Series




































Reviews: