manualshive.com logo in svg

Takara Belmont Yume Oasis, Installation Instructions Manual

Share
Download
Takara Belmont Yume Oasis Installation Instructions Manual Download Page 4

○

 Ensure that the material or finishing of the floor surface is waterproof or has a waterproof coating applied.

○

 Always ensure that the floor surface is horizontally level.

○

 Ensure that the floor surface is smooth and free from bumps around the attachment areas.

○

 Prevent the step height of floor joint.

○

 Be sure to use a floor panel of 3 mm thickness.

○

 Use a hard floor panel made of polyvinyl chloride (PVC) tiles, etc.

○

 Do NOT use a cushion floor. Using a cushion floor may cause troubles in detaching and attaching the upper unit.

○

 For installation of upstairs, make sure to take appropriate waterproof measures.

○

 Do not use a floor panel with significant bumps or dents that disturb transfer of the upper unit. 

○

 Do not use a floor panel that becomes slippery when water is leaking. 

○

 Use the waterproof material for the floor.

○

 If the product is installed on the floor above a room, always make sure to take appropriate waterproof measures 

   (waterproofing work, installation of a stainless steel pan, attachment of a leakage sensor, etc.). 

○

 This company will not bear any responsibility whatsoever for water leakage due to the waterproof installation failure.

■

 Floor Surface

■

 Water Leakage

   Make sure to prevent the water leakage for the worst.

■

 Installation Of Pipes

■

 Plumbing

●

 Diameter of pipes and gradient of drain line

●

 Drainpipe end treatment (Ascending part dimensions) 

The following are important points to adhere to during the installation of pipes.

Read through the details carefully and ensure that the pipes are installed correctly.

・

When installing this product, ensure that installation of pipes adheres to the instructions outlined in "CAUTIONs during 

installation of pipes". Installing pipes without reading through the CAUTIONs will mean water may not mix properly, 

and a set temperature will not be achieved.

・

This product is designed for indoor installation.  Always install this product indoors.

Refer to the 

Plumbing Drawing

 on page 2. 

・

Use dependent drainage for YUME OASIS only.

・

Layout the drain line in a straight line as best as possible.

Number of upper units to

be used simultaneously

Diameter of Drainpipe

Gradient of drain line

2 units or less

3 units or more

At least VU 50

At least VU 75

＜

CAUTION

＞

Use a drainpipe of appropriate diameter according to the

number of units to be installed.

At least 1/100

At least 1/50

4

CAUTION

Make sure that the drainpipe does not have double trapping. 

Drain failure or abnormal noises may occur. 

Summary of Contents for Yume Oasis





































Reviews:

No comments

Brands by name

Popular brands

Load more brands