manualshive.com logo in svg

Takara Belmont Yume Oasis, Installation Instructions Manual

Share
Download
Takara Belmont Yume Oasis Installation Instructions Manual Download Page 10

Decorative floor panel 

32

㎜

Decorative floor panel 

Rafter for mounting 
(45 mm square) 

Resin case 
of floor unit

・

Machine screws for use (packaged with floor unit) 

   ø3.8 x 51 Coarse-led (SUS)

Sash

Finishing material 

24

㎜〜

30

㎜

※

 Check the flexural level of the floor base panel again and place additional support legs under the reinforcement frame if required. 

Rafter for mounting (45 mm square) 

90

㎜

90

㎜

591

㎜

431

㎜

10

５ 

Lamination of floor panels 

※

Dimensions of the reinforcement frame for unit mounting

CAUTION

The floor unit is fastened by machine screws at 32 mm high 
from the floor level.
Make sure to arrange the rafter for fastening at the height. 

※

 The adjustable range of floor unit is up to 150 mm from 

 floor level.
 For raising the floor level over 150 mm, provide a base 
 inside of the reinforcement frame with rick, block, 
 and mortar, etc.

[Illustration of rafters] 

Maximum length;
 up to 150 mm

135

㎜

Floor unit 

Rafter

Composite panel

591

～

592

㎜

431

～

432

㎜

90

㎜

90

㎜

Subflooring material (t 12) 

Finishing material (t 12) 

Support Leg 

After laying the subflooring material and the finishing material on the base, attach the reinforcement frame 
for unit mounting onto the back surface of the subflooring material.

※

 Do NOT use wood for the base. 

 The level adjusters may sink down.

※

 If the base is unstable, securely fix it using mortar 

or glues.

     Maximum adjustable range: 

up to 15 mm

※

Adjuster Position

372

128

35

175

175

175

20

【

Unit

：㎜】

Summary of Contents for Yume Oasis





































Reviews:

No comments

Brands by name

Popular brands

Load more brands