background image

8

Time Setting Key

Mist Level Lamp

Light

Heavy

1

2

3

4

Use this to change the time that has been set.
Pressing on

        (

 UP ) and       ( DOWN ) together will change 

the time in 1-minute increments each time they are pressed.
Keeping the keys depressed will change the time in 
succession (0 to 60 minutes).

Mist Level Key

Use this to change the amount of mist.
Pressing on it will increase the level by one 
each for time it is pressed.
(The level will revert to Level 1 after Level 4 
has been reached)

Control Panel

Level*

Mist Amount

Lamp Color

Yellow

Red

start /stop Key

Use this to start the operation of each mode.
Use this to stop operation.
Pressing the start key after a mode has been exited will 
result in starting under the settings that were in effect the 
time before. (Removing the power plug will invalidate the 
operating mode settings)

cooling Key

Select whether or not to use cooling after the Mist 
operation stops.
(Cooling is ON when the lamp is lit)

*

In operation at a low Mist Level setting (1, 2) no mist may be visible to the naked eye for a short 

 period after operation begins (about a minute); however, a misty breeze is actually being emitted.
 This is not a malfunction.

Summary of Contents for Ak-200





















Reviews:

Related manuals for Ak-200