background image

3

 

Dear Customer, 
 
By purchasing our firewood processor you obtained the equipment which will provide you with great help in 
your work. To make operating the machine as safe and pleasant as possible, please carefully read this 
operating instructions and follow the safety and maintenance directives. 
We would like to thank you for your trust and wish you great satisfaction in your work.  

1. GENERAL  

1.1. MANUFACTURER’S ADDRESS  

Tajfun Planina, d.o.o., Planina 41a, 3225 Planina pri Sevnici, Slovenia 

Tel.: 

+386 (0)3 746 44 00

, Fax.: 

+386 (0)3 579 10 16

, E-mail: 

[email protected]

www.tajfun.com

 

Feed Conveyor 

Sawbar activation Handle

 

Machine Cover with Safety Switch 

Discharge Conveyor

 

Splitting Cylinders Control Handle 

Discharge Conveyor’s speed Regulator

 

Handle for regulation of Feed Conveyor’s turning 
direction 

Splitting Wedge Handle

 

Log Loader Control Handle 

Retaining Handle

 

Low pressure Gauge 

Main Switch (RCA 380 E)

 

High pressure Gauge – Splitting 

»Start –Stop« Switch (RCA 380 E)

 

Discharge Conveyor Valve (Check-choke valve) 

 

 

RCA 380 

RCA 380 E 

Summary of Contents for RCA 380

































Reviews: