749161-101
Made in China
2014
connected to the same outlet, they only need to be within range of the remote).
TIP
– If you want to return the set (or sets if you have more than one) back to Function 1 at any time, just push both the
“FUNCTION ” and “RESET” buttons at the same time for about 2 seconds until the set returns to Function 1. This resets the
unit back to Function 1 so you can start over and in case you are not sure which function you are on.
Light Set Functions
The light set when used in conjunction with the remote control has 7 different preprogrammed functions. To change the functions of the
light set, you must use the remote control, so it is important to keep it in a safe place.
The remote will work through most windows and walls, and does not require a line of sight between the remote and light string, so you
can comfortably use the remote inside your home to change your lights if used outdoors.
Light Set Functions:
1.
Chase – Fade between colors
5. Fade and color change
2.
Growing color change
6. Fade between colors
3.
Single fast color change
7. Flash between colors
4.
Chase-Fade color change
The light sets have a memory of the last function they were used in. Each time you turn them off (by using the remote or by
disconnecting power to the set) they will turn on in the same function they were turned off at.
NOTE –
If product is turned off with a remote, and then it is attempted to turn them on by plugging in or turning on a wall switch, the
lights will not come on as it will remember the last function that it was turned off at, including if the remote was used to turn the set off.
In this case, after applying power to the set, turn the lights on using the power button on the remote.
Using the Set
Plug light string into a 110V – 125V wall receptacle, lights will turn on. Press power button on remote if they
do not turn on when first plugged in.
Fully extend the antenna and push the button marked “Function” on remote to advance to next function
(after lights are turned on).
In case you are not sure which function you are on, you can return the set(s) back to Function 1 (Chase-
Fade between colors) by pressing both the “function” and “reset” buttons at the same time for approximately
2 seconds.
Note:
the red LED at the top of the remote will illuminate with each press of a button on the remote. If the
LED does not illuminate, install or replace the battery in the remote.
Additional Notes for Using a Set:
1.
Lights must be plugged into working outlet for the light set and remote control to function.
2.
The remote control unit is the only way to change the function setting of this product.
3.
When using the remote to turn your set ON, there may be a slight delay before the light function starts working.
4.
To change the light function, it is recommended to wait a few seconds after each time you press the “FUNCTION” button until
you reach the desired function.
5.
If the lights do not change function or the set does not turn on or off with the remote, see the trouble shooting section.
6.
If there is a power interruption, including if used on a switched outlet, on a timer, or power failure, the system’s memory will
retain the last light function displayed.
7.
The operating distance of the remote is up to 90 feet (27.4 meters). Distance may vary due to other radio transmitters in the
area (cell phones, WiFi signals, wireless phones, intercoms, baby monitor, etc.), microwave ovens, computers, materials used
in the construction of your home, trees, hills, bushes and other items that may attenuate the radio signal.
8.
The battery in the remote will drain and become depleted very quickly if the remote is placed where one (or both) of the
buttons on the remote are continually pushed (such as placing an item on top of them, or storing the remote upside down).
Synchronizing Multiple Sets
1.
Plug all the light strings into any 110V – 125V wall receptacle, lights will turn on. Press power button on remote if they do not
turn on when first plugged in. Light sets do not have to be connected end to end or to the same outlet to be synchronized, but
must be within the range of the remote control (up to 90 feet (27.4 meters) distance may vary).
2.
Please be sure not to overload any outlets or extension cords when connecting multiple light strings.
3.
Fully extend the antenna on the remote.
4.
Push the power button if all lights are not already on. If only one or several lights are on, unplug those that are on, and while
plugged in, push the power button to turn on the rest of the lights, then reconnect the other lights so that all will be on.
