background image

M038020E 

 

Daily Inspection      

                                                  25                                               

Daily Inspection

 

Daily Inspection 

 

Inspect the radio-control system at the time of the pre-operational inspection of the main 
unit of the crane. 
 
(1) 

Is the case of the transmitter or control 
unit damaged? Do switches or rubber 
parts of the transmitter have any crack 
or flaw?

 

 
Any damage on the case or any crack or 
flaw on the rubber parts may allow water 
or dust to enter inside, causing electronic 
circuit problems or malfunction of the 
crane.  

 

(2) 

Do the motion selection switches and 
speed control lever move smoothly?

 

 
Adhered dust or dirt may give unfavorable 
impact on operations of the motion 
selection switches or speed control lever, 
causing operation failures or malfunctions 
of the crane. 

 
(3) 

Is the fixing screw of the transmitter’s 
battery cover securely tightened?

   

 
A loose fixing screw of the transmitter’s 
battery cover may allow water or dust to 
enter inside, causing electronic circuit 
problems or malfunction of the crane. 

 
(4) 

Is the cable between the control unit 
and communication unit loose or 
damaged? 
Is the antenna of the communication 
unit damaged or loose?

   

 
If the connector of the cable or antenna is 
loose, a radio wave reaching distance 
may be reduced or the radio-control 
system may be subject to noises. 
 
In addition, if the cable or antenna is 
damaged, the radio-control system may 
be subject to noises. 

 

 

M22681

M22682

M22680E

株式会社タダノ

製造番号

0200ES2

RCS-FR1

IC    :*****-RCSFR1
FCC ID:***-RCS-FR1
…………………………

…………………………

…………………………

…………………………

…………………………

………………

株式会社タダノ

製造番号

0200ES2

RCS-FR1

IC    :*****-RCSFR1
FCC ID:***-RCS-FR1
…………………………

…………………………

…………………………

…………………………

…………………………

………………

Transmitter

Communication unit

Control unit

M22679E

Summary of Contents for RCSFT1-433


































Reviews: