4
5
FASTENING TOOLS
FOR THE PROFESSIONAL
FIG. C - LOADING THE FASTENERS
FIG. D - AIR DEFLECTOR
FIG. E - TRIGGER LOCK
1
2
3
5
EN
23G Headless Pinner A6422V
Congratulations!
On the purchase of your Tacwise power tool. Your tool will perform
to your satisfaction for a long time if handled in accordance with our
Safety and Operating instructions.
Save this manual for future reference
Technical Data
Characteristic
Value
Minimum operating air pressure 60psi
Maximum operating air pressure 100psi
Nail length range
12mm (1/2") - 22mm (7/8")
Nail size
23GA Brads
Magazine capacity
100
Air inlet
1/4" NPT
Air consumption
0.6 CFM @ 90psi
Weight
0.8kgs (1.8lbs)
Vibration emission level*
2.35m/s
2
* The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase
exposure level over the total working period.
CE – Declaration of Conformity
23G Headless Pinner A6422V
Tacwise declares that this power tool has been designed in
compliance with the Regulations and Standards of the
European Directives.
Quality Department, Tacwise Group Plc – UK
WARNING! Before Use Carefully Read And Understand
All Instructions.
Failure to do so could result in fire and/or serious personal injury.
For any queries relating to safety matters on this power tool, please
email
.
Unpacking
• Carefully remove the tool and accessories from the box.
• Inspect the tool carefully to make sure no breakage or damage
occurred during transit.
• If any parts are damaged or missing, please email
for assistance. Do not operate this tool
until the missing or damaged parts are replaced. Failure to do so
could result in a personal injury.
• Whilst every effort has been made to ensure accuracy of
information contained within this manual, the Tacwise policy is
one of continuous improvement to our products and as such
we reserve the right to change the product specification without
prior notice.
General Safety Instructions
Important.
Tacwise recommends that this power tool should not
be modified or used for any application other than that for which
it was designed. Any such alteration or modification is misuse and
could result in a hazardous condition leading to a personal injury. If
you are unsure of its relative applications do not hesitate to contact
us and we will advise you.
Work Area
•
Keep your work area clean and well lit.
Cluttered benches and
dark areas invite accidents.
•
Keep children and pets away.
All visitors should be kept a safe
distance from work area.
•
Secure work.
Use clamps or a vice to hold work. This frees both
hands to operate the power tool.
Safety Warnings & Cautions
•
Never use oxygen combustible gases, bottled gases or high
pressure compressed gas as a power source for this tool.
The tool may explode and cause serious injury.
•
Outdoor extension cords.
When air compressor is used
outdoors, use only rounded jacket extension cords intended for
outside use. See manufacturer’s manual for the AWG required for
the compressor’s amperage draw.
•
Pay attention to air hose and their connections.
Don’t trip over
hoses. Make sure all connections are tight.
•
Use the correct air connector.
The connector on the tool must
not hold pressure when the air supply is disconnected. If the
wrong fitting is used, the tool can be charged with air after being
disconnected and still be able to drive a fastener.
•
When connecting the air.
The tool may possibly fire the
fasteners as soon as you plug it in to the air hose. Therefore,
remove all the fasteners before connecting to the air.
• Do not depress the trigger when loading.
•
If the fasteners are jammed.
Disconnect the tool from the air
and remove the jammed fasteners.
•
Stay alert.
Always watch what you are doing and use common
sense. Do not operate a power tool when you are tired or under
the influence of medication, alcohol or drugs.
•
Wear proper clothing.
Do not wear loose clothing or
jewellery that can catch in moving parts. Non-slip footwear is
recommended. Contain long hair and roll long sleeves above
the elbow.
•
Do not over reach or use on unstable surfaces.
Keep proper
footing and balance at all times.
•
Use safety equipment.
Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate
conditions. Wear CE approved safety goggles at all times. Normal
spectacles only have impact resistant lenses; they are NOT safety
glasses.
•
DO NOT use on hard surfaces
such as rock, concrete, masonry,
bricks or steel. Personal injury or damage to the power tool
could result.
•
Stored power tools.
When not in use, all power tools should be
stored in a dry, locked cupboard, out of the reach of children and
other untrained persons.
•
Recommended accessories.
Use only accessories that are
recommended by the manufacturer for your model. Accessories
that may be suitable for one tool may create a risk of injury when
used on another tool.
•
Beware of hidden danger.
Always make sure there is no danger
of hitting any hidden power cables, water or gas pipes.
•
Always assume that the tool is loaded with fasteners.
Handling the tool without care could result in an unexpected
firing of fasteners and lead to personal injury.
•
Do not activate the power tool unless it is in contact with the
work piece.
Serious injury can result if you depress the
safety lock pin on nose/contact trip with your fingers, or by
improper operation.
