background image

18

Special functions

Menu “4. Special functions” is used to set basic 

items and expanded functions.

The  menu  is  closed  by  pressing  “esc”  or 

selecting “Exit special functions”.

4. - Special functions

Caution

Other than the time all settings may 

only be made by a specialist.

This menu is used to set the current time and date.

4.1. - Time & date

Caution

For analysis of the system data it is essential for the time to be set accurately 

on the controller. Please note that the clock does not continue to run if the mains 

voltage is interrupted, and must therefore be reset.

Deviations in the temperature values displayed, for example due to cables which are to 

long or sensors which are not positioned optimally, can be compensated for manually 

here. The settings can be made for each individual sensor in steps of 0.5°C.

Offset S1...S3 per setting range: -100 to +100 (translates to -50°C...+50°C)

Default setting: 0

4.2. - Sensor calibration

Caution

Settings are only necessary in special cases at the time of initial com-

missioning by the specialist. Incorrect measurement values can lead to 

unpredictable errors.

Starting the commissioning help guides you in the correct order through the basic set-

tings necessary for commissioning, and provides brief descriptions of each parameter 

in the display.

Pressing the “esc” key takes you back to the previous value so you can look at the se-

lected setting again or adjust it if desired. Pressing the “esc” more than once takes you 

back to the selection mode, thus cancelling the commissioning help. (see also E.2).

4.3. - Commissioning

Caution

May only be started by a specialist during commissioning! Observe the 

explanations for the the individual parameters in these instructions, and 

check whether further settings are necessary for your application.

Summary of Contents for FWCK

























Reviews: