background image

TPF / TFB Series Floor Scale Service Manual 

 

- 13 - 

 
 

6.8 Parts Replacement: 

 
Load Cell Replacement: 
 

                                   

 

 
 
 
 
 

 

  Remove power from the Indicator terminal and disconnect the instrument 

cable. 

  Remove the junction box cover and locate the defective load cell. 

 

Disconnect the defective load cell’s cable from its terminal on the junction 
box PCB (Summing PCB). 

  Remove the load cell from the junction box. 

  Carefully position the platform on a stable supporting surface that allows 

access to defective load cell and cable. 

  Tie a string to the end of the cable attached to the defective load cell. The 

string should be strong and long enough to pull the new load cell’s cable 
through the platform structure. 

  The load cells (s) are fastened to the platform using two Head Cap Bolts. 

Remove this load cell mounting bolts with a box spanner, retaining the 
screws for reinstallation. Lift the load cell and spacer plate from the 
mounting surface. 

  Carefully pull the defective load cell cable through the platform while 

feeding the string in at junction box opening. Once the string reaches the 
load cell mounting location, untie it from the load cell cable. 

Spacer 

Load Cell 

Flat Washer 

Spring Washer 

Bolt 

Adjustable 
Foot 

Summary of Contents for TFB sereis























Reviews: