background image

Warnings |

1

1

Warnings

The following admonitions will be presented in the different sections of the document.

Danger

• Make sure that the Mains supply to the unit is disconnected before performing any maintenance or

electrical work!

• All electrical connections must be carried out by an authorized installer and in accordance with local rules

and regulations.

• Operation in the refrigerant circuit and handling refrigerants must be performed by certified personnel.

Warning

• Beware of sharp edges during mounting and maintenance. Use protective clothing.

• Skin contact with the refrigerant must be avoided. Use protective equipment such as protective goggles,

gloves and suitable clothing’s. Good ventilation must be arranged.

If freezing injury a doctor must be seen.

If skin contact the exposed part of the body must be carefully washed.

If eye contact use eye wash or lukewarmed water and wash for 20 minutes, visit a doctor.

• The units electrical connection to the mains supply must be preceded by an all pole circuit breaker with a

minimum 3 mm gap.

• This product is not intended to be used by children or people with reduced physical or mental ability or

lack of experience and knowledge, if no instruction concerning the use has been given by the person
responsible for their safety or that this person is supervising the operation. Children should be supervised
so that they can not play with the product.

2

Product description

2.1

Components

Fig. 1 Basic components in left hand unit

208766 | A003

Summary of Contents for Topvex SoftCooler SR09





















Reviews: