background image

152020

Warranty    |         5

2.1     

  Personnel

The fan may only be used by qualified, instructed and trained personnel. The persons must know the relevant safety directives in order 
to recognize and to avoid risks. The individual activities and qualifications can be found in Table 1 

Qualifications

, below.

Table 1 Qualifications

Activities

Electrical expert or

matching qualification

Fitter or matching

qualification

Trained personnel (see

following note)

Storage, operation, 

transport, cleaning, disposal

X

Electrical connection, commissioning, 

electrical disconnection 

X

Installation, disassembly

X

Maintenance

X

X

Repair

Smoke extraction fans and EX fans only by agreement with Systemair.

Note:

The operator is responsible for ensuring that personnel are instructed and have understood the contents of the operating 

instructions. If something is unclear, please contact Systemair or its representative.

i

2.2  

  Personal protective equipment

Wear protective equipment during all work in the vicinity of the fan.

 

 

•  protective working clothes 

•  protective working gloves 

•  goggles

 

•  protective working shoes 

•  helmet 

 

 

•  hearing protection

2.3  

  5 rules of electrical safety

•  Disconnect (disconnection of the electrical system from live components at all terminals)

•  Prevent reactivation

•  Test absence of voltage

•  Ground and short-circuit

•  Cover or restrict adjacent live parts

3  

  Warranty

The warranty for our products is determined by the contractual stipulations, our offers and our Terms and Conditions. Warranty claims 

presuppose that the product is properly connected, operated according to data sheets and serviced as needed. A correct commissioning

report must also be presented upon request. Please find the commissioning report attached to this document.

4  

  Delivery, transport, storage

4.1  

  Safety information

Warning: Risk from rotating fan blades

◊ Prevent access by unauthorized persons by safety personnel or access protection.

Warning: Suspended loads

◊ Wear protective equipment during all work in the vicinity of the fan, details see 2.2 

Personal protective equipment

, page 6.

◊ Do not walk under suspended loads.

◊ Make sure that there is nobody under a suspended load.

Summary of Contents for IV Smart AC





































Reviews: