SystemAir HHFlex C Operating Instructions Manual Download Page 41

Page: 41 / 47

Alarm Description

Reset Type

Probable cause

Action taken by the control

- Derated mode: Warning & go to low
fixed speed fan control
- Unit stopped

Supply Fan Pressure
Failure

Manual

Defective sensor or installation
fault

Unit stopped

Exhaust Fan Pressure
Failure

Manual

Defective sensor or installation
fault

Unit stopped

Pressure Drop across
Heat Exchanger Sensor
Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: Warning and frost
protection deactivated
- Unit stopped

Room Pollution Sensor
Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: Warning & Go to low
fixed speed fan control
- Unit stopped

External Fire

Manual /
Automatic
configurable
in the extra
settings menu

Input of the controller activated

Configurable in Actual/Setpoint Extra
settings
•

Supply-fan off, Extract-fan off

(default)
•

Supply-fan on, Extract-fan on

•

Supply-fan on, Extract-fan off

•

Supply-fan off, Extract-fan on

When “on” is selected, fan is running at
a configurable fixed fan speed

Battery low or missing,
Change it quickly

Automatic

Internal monitoring

Warning

Pump Collective Failure Automatic

Input of the controller activated

Warning

Supply Air Humidity
Sensor Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: humidifier disabled

Extract Air Humidity
Sensor Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu

Room Sensor Humidity
Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu

Maximum humidity

Manual

Input of the controller activated

Humidifier stopped

Summary of Contents for HHFlex C
















































Search results

Summary of Contents for HHFlex C

Reviews:

SystemAir HHFlex C, Operating Instructions Manual, Page: 41 / 47

Search results

Summary of Contents for HHFlex C

Reviews: