SystemAir HHFlex C Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 47

SystemAir HHFlex C Operating Instructions Manual Download Page 40

40

6.5 Alarms List

Alarm Description

Reset Type

Probable cause

Action taken by the control

Low Supply Air
Temperature Alarm

Automatic

Unit with heat recovery only
During 10 minutes, SAT < SAT
controlled point – 3 K

Unit is stopped for 50 minutes then
restarted.

High Supply Air
Temperature Alarm

Automatic

Unit with heat recovery only
During 10 minutes, SAT > SAT
controlled point + 3 K

Warning.

Heat Exchanger Failure

Manual

Input of the controller activated

Warning only, control signal to rotor is
cancelled

Extract Fan failure

Manual

Input of the controller activated

Unit stopped

Supply Fan failure

Manual

Input of the controller activated

Unit stopped

Electrical pre-heater
maximum temp alarm

Manual

Input of the controller activated

Electrical pre-heaters are stopped and
unit stopped after cool down delay

Electrical heater,
maximum temp alarm

Manual

Input of the controller activated

Electrical heaters are stopped and unit
stopped after cool down delay

Frost protection of pre
heat hot water coil

Manual

Input of the controller activated

Unit stopped, valves opened at 80% &
heat demand/pumps activated

Frost protection of
booster hot water coil

Manual

Input of the controller activated

Unit stopped, valves opened at 80% &
heat demand/pumps activated
Same reaction with change over water
coil

Supply Filter High Delta
P Alert

Manual

Input of the controller activated

Warning

Extract Filter High Delta
P Alert

Manual

Input of the controller activated

Warning

End Filter High Delta P
Alert

Manual

Input of the controller activated

Warning

Supply Pressure Filter
Failure

Manual

Defective sensor or installation
fault

Warning

Exhaust Pressure Filter
Failure

Manual

Defective sensor or installation
fault

Warning

Pressure End Filter
Failure

Manual

Defective sensor or installation
fault

Warning

Inlet Air Temperature
Sensor Failure

Automatic

Defective sensor or installation
fault

Warning, no more pre-heater control and
heat recovery at 100%

Supply Air Temperature
Sensor Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: Warning, boosters
stopped & heat recovery at 100%
- Unit stopped

Extract Air Temperature
Sensor Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: Warning & go to SAT
control with heat recovery at 100%
- Unit stopped

Room Sensor
Temperature Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu
- Derated mode: Warning, go to SAT
control, no more summer night
ventilation and room temp surveillance
- Unit stopped

Outdoor Air
Temperature Sensor
Failure

Automatic

Defective sensor or installation
fault

Warning & no more OAT compensation,
no more summer night ventilation
- Unit stopped

Supply Air Pressure
Sensor Failure

Automatic

Defective sensor or installation
fault

Configurable in Actual/Setpoint Config.
menu

«
...
38
39
40
41
42
...
»

Summary of Contents for HHFlex C
















































Reviews:

No comments