background image

System  Sensor  warrants  its  enclosed  air  duct  smoke  detector  to  be  free 
from  defects  in  materials  and  workmanship  under  normal  use  and  ser-
vice for a period of three years from date of manufacture. System Sensor 
makes  no  other  express  warranty  for  this  air  duct  smoke  detector.  No 
agent, representative, dealer, or employee of the Company has the author-
ity to increase or alter the obligations or limitations of this Warranty. The 
Company’s  obligation  of  this  Warranty  shall  be  limited  to  the  repair  or 
replacement of any part of the air duct smoke detector which is found to 
be defective in materials or workmanship under normal use and service 
during the three year period commencing with the date of manufacture. 
After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672) 
for a Return Authorization number, send defective units postage prepaid 
to:  System  Sensor,  Repair  Department,  RA  #__________,  3825  Ohio 

D500-07-00 

11 

I56-432-11R

Please refer to insert for the Limitations of Fire Alarm Systems

Three-Year Limited Warranty

Avenue, St. Charles, IL 60174. Please include a note describing the mal-
function and suspected cause of failure. The Company shall not be obli-
gated to repair or replace units which are found to be defective because 
of  damage,  unreasonable  use,  modifications,  or  alterations  occurring 
after the date of manufacture. In no case shall the Company be liable for 
any consequential or incidental damages for breach of this or any other 
Warranty, expressed or implied whatsoever, even if the loss or damage is 
caused by the Company’s negligence or fault. Some states do not allow 
the exclusion or limitation of incidental or consequential damages, so the 
above limitation or exclusion may not apply to you. This Warranty gives 
you specific legal rights, and you may also have other rights which vary 
from state to state.

Summary of Contents for DH500ACDC













Reviews: