Synel PRX-40 B Product Manual Download Page 11

Page: 11 / 18

PRX-40B

4.5

Jumpers

4.6

Dismounting the terminal

Remove the security screw from the top of the unit.

Press the clasps at the bottom of the mounting panel and lift the unit upward.

Jumper

Function

Default

JP2 (SMD)

JP2 closed and JP3 open = Linear decoding
JP2 open and JP3 closed = Synel decoding

Linear

JP3 (SMD)

JP4 (SMD)

Cross point decoding (currently NA)

JP7 (SMD)

Connect RS-485 termination resistor

Open

JP10 (TH)

W.D. Reset for the master CPU- [1-2] Closed
Programming of the master CPU - [2-3] Closed

[1-2] closed

JP11(TH)

PSEN (Programming) - must be closed when programming the master
CPU.

Open

JP12 (SMD)

Tamper switch enabled [1-2] closed
Tamper switch disabled [2-3] closed

[2-3] closed

JP20 (T.H)

Closed- Stand alone
Open- Online with Master

Closed
(up to version 3.04
later set via Setup)

JP21 (T.H)

Contacts switching protection in DC- closed
Contacts switching protection in AC- open

Closed

JP22 (SMD)

Connecting clock to slave CPU

[2-3] closed

JP23 (T.H)

Select sensor option:
[1-2] and [3-4] Closed - dry contact
[2-3] Closed - AC/DC

[1-2] and [3-4] closed

JP24 (T.H)

Reset for the slave/reader CPU- [2-3] closed
Programming of the slave/reader CPU [1-2] Closed

[2-3] closed

Summary of Contents for PRX-40 B



















Search results

Summary of Contents for PRX-40 B

Reviews:

Related manuals for PRX-40 B

Brands by name

Popular brands

Synel PRX-40 B, Product Manual

Search results

Summary of Contents for PRX-40 B

Reviews:

Related manuals for PRX-40 B

Brands by name

Popular brands