Symmons Duro Series Operation & Maintenance Manual Download Page 7

Symmons Industries, Inc.  

  31 Brooks Drive  

  Braintree, MA 02184  

  Phone: (800) 796-6667  

■  

Fax: (800) 961-9621

Copyright © 2016 Symmons Industries, Inc.  

  www.symmons.com  

  [email protected]  

  ZV-3017 REV B  

■  

100316

Troubleshooting Chart

Finish is spotting.

Elements in water supply may cause 

water staining on finish.

Clean finished trim area with a soft 

cloth using mild soap and water or a 

non-abrasive cleaner and then quickly 

rinse with water.

Operation (Diverter Control: 2DIV-BODY)

POSITION 1

POSITION 2

1)  Cartridge is factory set to divert 

to function 1.

2)  Turn handle to position 2 to divert 

to function 2.

3)  Turn handle to position 3 to share  

functions 1 and 2.

POSITION 3

Note: 

Additional handle positions for same output are illustrated.

Operation (Diverter Control: 3DIV-BODY)

1)  Cartridge is factory set to divert 

to function 1.

POSITION 2

2)  Turn handle to position 2 to divert 

to function 2.

POSITION 1

POSITION 3

POSITION 6

3)  Turn handle to position 3 to divert 

to function 3.

6)  Turn handle to position 6 to share 

functions 1 and 2.

Troubleshooting Chart

5)  Turn handle to position 5 to share 

functions 1 and 3.

POSITION 5

POSITION 4

4)  Turn handle to position 4 to share 

functions 2 and 3.

For California Residents

WARNING:

 This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Summary of Contents for Duro Series








Reviews: