Symetrix Room Combine 788 Quick Start Manual Download Page 3

3

Integrator Series Room Combine 788

G

 

The lightning flash

 with arrowhead 

symbol within an equilateral triangle is 
intended to alert the user of the presence 
of uninsulated “dangerous voltage” 
within the product’s enclosure that may 
be of sufficient magnitude to constitute 
a risk of electric shock to persons. The 
exclamation point within an equilateral 
triangle is intended to alert the user of 
the presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the product (i.e. 
this Quick Start Guide).

G

 

CAUTION:

 To prevent electric shock, 

do not use the polarized plug supplied 
with the unit with any extension cord, 
receptacle, or other outlet unless the 
prongs can be fully inserted.

G

 

Power Source:

 This Symetrix hardware 

uses a switching power supply that 
automatically adjusts to the applied 
voltage. Ensure that your AC mains 
voltage is somewhere between 100-240 
VAC, 50-60 Hz. Use only the power 
cord and connector specified for the 
product and your operating locale. A 
protective ground connection, by way of 
the grounding conductor in the power 
cord, is essential for safe operation. The 
appliance inlet and coupler shall remain 
readily operable once the apparatus has 
been installed.

G

 

User Serviceable Parts:

 There are no 

user serviceable parts inside this Symetrix 
product. In case of failure, customers 
inside the U.S. should refer all servicing to 
the Symetrix factory. Customers outside 
the U.S. should refer all servicing to an 
authorized Symetrix distributor. Distributor 
contact information is available online at: 
http://www.SymetrixAudio.com.

AVIS:

NE PAS OUVRIR

Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.

SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.

S’adresser a un reparateur compétent.

RISQUE DE CHOC ELECTRIQUE

No user serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION

WARNING:

TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE

DO NOT OPEN

RISK OF ELECTRIC SHOCK

Important Safety  
Instructions

!

  Read these instructions.

@

  Keep these instructions.

#

  Heed all warnings.

$

  Follow all instructions.

%

  Do not use this apparatus near water. 

This apparatus shall not be exposed to 
dripping or splashing and no objects 
filled with liquids, such as vases, shall be 
placed on the apparatus.

^

  Clean only with dry cloth.

&

  Do not block any ventilation openings. 

Install only in accordance with the 
manufacturer’s instructions.

*

  Do not install near any heat sources such 

as radiators, heat registers, stoves, or 
other apparatus (including amplifiers) that 
produce heat.

(

  This apparatus shall be connected to 

a mains socket outlet with a protective 
earthing connection. Do not defeat 
the safety purpose of the polarized or 
grounding-type plug. A polarized plug has 
two blades with one wider than the other. 
A grounding type plug has two blades 
and a third grounding prong. The wide 
blade or the third prong are provided for 
your safety. If the provided plug does not 
fit into your outlet, consult an electrician 
for replacement of the obsolete outlet.

BL

  Protect the power cord from being 

walked on or pinched particularly at 
plugs, convenience receptacles, and the 
point where they exit from the apparatus.

BM

  Only use attachments/accessories 

specified by the manufacturer.

BN

  Use only with the cart, stand, 

tripod, bracket, or table 
specified by the manufacturer, 
or sold with the apparatus. 
When a cart is used, use 
caution when moving the cart/apparatus 
combination to avoid injury from tip-over.

BO

  Unplug this apparatus during lightning 

storms or when unused for long periods 
of time.

BP

  Refer all servicing to qualified service 

personnel. Servicing is required when 
the apparatus has been damaged in any 
way, such as power-supply cord or plug 
cord is damaged, liquid has been spilled 
or objects have fallen into the apparatus, 
the apparatus has been exposed to rain 
or moisture, does not operate normally, or 
has been dropped.

What Ships In the Box

•  Room Combine 788 hardware device.
•  Room Combine 788 CD-ROM 

(Windows).

•  Detachable power cord.
•  25 detachable Phoenix (or Euroblock, 

as applicable) connectors.

•  This Quick Start Guide.

What You Need to Provide

•  A Windows

®

 PC with 1 GHz or higher  

processor and:

•  Windows XP or Vista.
•  250 MB free storage space.
•  1024x768 graphics capability.
•  16-bit or higher colors.
•  CD-ROM drive or Internet connection.
•  512 MB or more of RAM as required by 

your operating system.

•  Network (Ethernet) interface.
•  CAT5 cable or an existing Ethernet 

network.

Getting Help

Room Combine 788, the Windows 
application that controls the hardware, 
includes a help module which acts as a 
complete User’s Guide for both hardware 
and software. If you have questions 
beyond the scope of this Quick Start 
Guide or the software help file, contact 
our Customer Support Group in the 
following ways:

Tel:  +1.425.778.7728
 

8:00 am to 4:30 pm

 

Monday through Friday,

 

Pacific Time

Web: http://www.SymetrixAudio.com

This device complies with part 15 of 
the FCC Rules. Operation is subject 
to the following two conditions: (1) 
This device may not cause harmful 
interference, and (2) this device must 
accept any interference received, 
including interference that may cause 
undesired operation.

This Class B Digital apparatus meets 

all requirements of the Canadian 
Interference-Causing Equipment 
Regulations
Cet appariel numerique de la classe 

B respecte toutes les Exigences du 

Reglement sur le materiel brouilleur  
du Canada.

Safety

Summary of Contents for Room Combine 788





























Reviews: