the SOFTWARE with the DEVICE is otherwise allowed in this EULA; (ii) your rights with respect to any SOFTWARE upgrades
shall be as determined by the lease you signed for the DEVICE; and (iii) you may not use the SOFTWARE after your lease
terminates, unless you purchase the DEVICE from SYMBOL TECHNOLOGIES, INC.
•
Software Transfer.
You may permanently transfer all of your rights under this EULA only as part of a sale or transfer of
the DEVICE, provided you retain no copies, you transfer all of the SOFTWARE (including all component parts, the media
and printed materials, any upgrades, this EULA and, if applicable, the Certificate(s) of Authenticity), and the recipient
agrees to the terms of this EULA. If the SOFTWARE is an upgrade, any transfer must include all prior versions of the
SOFTWARE.
•
Termination
. Without prejudice to any other rights, SYMBOL TECHNOLOGIES, INC. or MS may terminate this EULA if
you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the
SOFTWARE and all of its component parts.
UPGRADES AND RECOVERY MEDIA.
•
DEVICE Software
. If the DEVICE Software is provided by SYMBOL TECHNOLOGIES, INC. separate from the DEVICE on
media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes
Only” you may install one (1) copy of such DEVICE Software onto the DEVICE as a replacement copy for the existing
DEVICE Software, and use it in accordance with this EULA, including any additional EULA terms accompanying the
upgrade DEVICE software.
•
COMPANION CD
. If any software component(s) is provided by SYMBOL TECHNOLOGIES, INC. separate from the
DEVICE on CD ROM disk(s) or via web download or other means, and labeled “For Upgrade Purposes Only”, you may (i)
install and use one (1) copy of such component(s) on the computer(s) you use to exchange data with the DEVICE as a
replacement copy for the existing Companion CD component(s).
COPYRIGHT.
All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images,
photographs, animations, video, audio, music, text and “applets,” incorporated into the SOFTWARE), the accompanying
printed materials, and any copies of the SOFTWARE, are owned by MS or its suppliers (including Microsoft Corporation).
You may not copy the printed materials accompanying the SOFTWARE. All title and intellectual property rights in and to the
content which may be accessed through use of the SOFTWARE is the property of the respective content owner and may be
protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such
content. All rights not specifically granted under this EULA are reserved by MS and its suppliers (including Microsoft
Corporation).
EXPORT RESTRICTIONS
. You acknowledge that SOFTWARE is subject to U.S. export jurisdiction. You agree to comply
PRODUCT SUPPORT
. Product support for the SOFTWARE is not provided by MS, its parent corporation Microsoft
Corporation, or their affiliates or subsidiaries. For product support, please refer to SYMBOL TECHNOLOGIES, INC.support
number provided in the documentation for the DEVICE. Should you have any questions concerning this EULA, or if you desire
to contact SYMBOL TECHNOLOGIES, INC. for any other reason, please refer to the address provided in the documentation
for the DEVICE.
NO LIABILITY FOR CERTAIN DAMAGES
. EXCEPT AS PROHIBITED BY LAW, MS SHALL HAVE NO LIABILITY FOR ANY
INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL
PURPOSE.
FOR APPLICABLE LIMITED WARRANTIES AND SPECIAL PROVISIONS PERTAINING TO YOUR PARTICULAR JURISDICTION,
PLEASE REFER TO YOUR WARRANTY BOOKLET INCLUDED WITH THIS PACKAGE OR PROVIDED WITH THE SOFTWARE
PRINTED MATERIALS.
Ergonomic Recommendations
Caution:
In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety
programs to prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural/neutral position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled
as required. Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol
Technologies, could void the user's authority to operate the equipment. Antenna's, use only the supplied or an approved
replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate
regulations.
Radio Modules
This device contains an approved radio module. This module is identified below:
• Symbol RLAN (11Mbps DSSS) radio module, Type: 21-64436.
Power Supply
Use only a Symbol-approved power supply output rated 11-16 Vdc and minimum 2A. The power supply is certified to
EN60950 with SELV outputs. Use of alternative power supply will invalidate any approval given to this device and may
be dangerous.
Benutzen Sie nur eine Symbol Technologies genehmigt in den Ausgabe: 11-16Vdc und minimum 2A. Die
Stromversorgung ist bescheinigt nach EN60950 mit SELV Ausgaben.
FCC RF Exposure Guidelines
Reducing RF Influence - Use Properly
It is advisable to use the device only in the normal operating position and it is recommended that no part of the human
body be allowed to come too close to the antenna during operation of the equipment.
Handheld Devices
To comply with FCC RF exposure requirements, this device must be operated in the hand and must operate with a
minimum separation distance of 20 cm or more from a person's body. Other operating configurations should be avoided.
Laser Devices
Symbol devices using lasers comply with US 21CFR1040.10, and IEC825-1:1993, EN60825-1:1994+A11:1996. The laser
classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following
statement is required to comply with US and international regulations:
Caution:
Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous laser light exposure.
•Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser
is not known to be harmful.
Scanner Labeling
LASERLICHT - NICHT IN DEN STRAHL BLICKEN.
LASER KLASSE 2
LUMI¨RE LASER -NE PAS REGARDER DANS
LE FAISCEAU APPAREIL LASER DE CLASSE 2.
CAUTION-LASER LIGHT. DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT 630-680 nM, 1 mW
Laser Labels
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
ENGLISH
HEBREW
CLASS 1
CLASS 1 LASER PRODUCT
CLASS 2
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
DANISH / DANSK
ITALIAN / ITALIANO
KLASSE 1
KLASSE 1 LASERPRODUKT
CLASSE 1
PRODOTTO AL LASER DI CLASSE 1
KLASSE 2
LASERLYF
CLASSE 2
LUCE LASER
SE IKKE IND I STRÅLEN
NON FISSARE IL RAGGIOPRODOTTO
KLASSE 2 LASERPRODUKT
AL LASER DI CLASSE 2
DUTCH / NEDERLANDS
NORWEGIAN / NORSK
KLASSE 1
KLASSE-1 LASERPRODUKT
KLASSE 1
LASERPRODUKT, KLASSE 1
KLASSE 2
LASERLICHT
KLASSE 2
LASERLYS IKKE STIRR INN I LYSSTRÅLEN
NIET IN STRAAL STAREN
LASERPRODUKT, KLASSE 2
KLASSE-2 LASERPRODUKT
FINNISH / SUOMI
PORTUGUESE / PORTUGUÊS
LUOKKA 1
LUOKKA 1 LASERTUOTE
CLASSE 1
PRODUTO LASER DA CLASSE 1
LUOKKA 2
LASERVALO
CLASSE 2
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
ÄLÄ TUIJOTA SÄDETTÄ
PRODUTO LASER DA CLASSE 2
LUOKKA 2 LASERTUOTE
FRENCH / FRANÇAIS
SPANISH / ESPAÑOL
CLASSE 1
PRODUIT LASER DE CLASSE 1
CLASE 1
PRODUCTO LASER DE LA CLASE 1
CLASSE 2
LUMIERE LASER
CLASE 2
LUZ LASER
NE PAS REGARDER LE RAYON FIXEMENT
NO MIRE FIJAMENTE EL HAZ
PRODUIT LASER DE CLASSE 2
PRODUCTO LASER DE LA CLASE 2
GERMAN / DEUTCH
SWEDISH / SVENSKA
KLASSE 1
LASERPRODUKT DER KLASSE 1
KLASS 1
LASERPRODUKT KLASS 1
KLASSE 2
LASERSTRAHLEN
KLASS 2
LASERLJUS STIRRA INTE MOT STRÅLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT KLASS 2
LASERPRODUKT DER KLASSE 2
Radio Frequency Interference Requirements
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications
were met.
JAPANESE /
ᣣᧄ⺆
ࠢࠬޓࠢࠬࠩຠ
ࠢࠬޓࠩశ✢
శ✢ࠍ⋥ⷞߒߥߢߊߛߐ
ࠢࠬࠩຠ
KOREAN /
G䞲ῃ㠊
X❇ G
X❇ G⩞㧊㩖G㩲䛞
Y❇ G
⩞㧊㩖Gὧ㍶
G
㧊Gὧ㍶㦚G㭒㔲䞮㰖GⰞ㕃㔲㡺U
G
Y❇ G⩞㧊㩖Gὧ㍶
CHINESE /
ㅔԧЁ᭛
1
㉏
1
㉏▔ܝѻક
2
㉏
▔ܝ
ߛ࣓⊼㾚ܝᴳ
2
㉏▔ܝѻક
