Symbol LS3008 Quick Reference Manual Download Page 15

Quick Reference Guide

15

eines anderen Netzteils werden alle für das Gerät gewährten Genehmigungen 
außer Kraft gesetzt, und der Betrieb kann gefährlich sein.

Radio Frequency Interference Requirements-FCC

Note:

 This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements - Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du 
Canada.

Marking and European Economic Area (EEA)

Statement of Compliance

Symbol Technologies, Inc., hereby declares that this device is in 
compliance with all the applicable Directives, 89/336/EEC, 73/23/EEC. A 
Declaration of Conformity may be obtained from 
http://www2.symbol.com/doc/.

Tested to comply
with FCC Standards

FOR HOME OR OFFICE USE

Summary of Contents for LS3008





















Reviews: