background image

3

English

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference 

unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an 

unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 

If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off 

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1)

 Reorient or relocate the receiving antenna.

2)

 Increase the separation between the apparatus and receiver.

3)

 Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4)

 Consult the dealer or an experienced radio/TV technician for help.

DECLARATION OF CONFORMITY

Trade Name:

 SYLVANIA   

Responsible Party:

FUNAI CORPORATION, Inc.

Model:

LC220 SS2 

Address:

19900 Van Ness Avenue, Torrance, CA 90501 U.S.A.

Telephone Number:

1-866- 321-3927  

This Class B digital apparatus complies with Canadian ICES-003.  Standard Television Receiving Apparatus, Canada BETS-7 / NTMR-7

CAUTION :   

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNING :   

Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnect the mains plug to shut off when find trouble or not in use. The mains plug shall remain readily operable.

This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.

Make sure to leave a space of 4 inches (10cm) or more around this apparatus.

WARNING: 

To prevent injury, this apparatus must be securely attached to the wall in accordance with the instructions.

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or 

climbing on it. A falling unit can cause serious injury or even death.

 LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.

NOTE ABOUT RECYCLING

 

•  This unit’s packaging materials are recyclable and 

can be reused. Please dispose of any materials in 

accordance with your local recycling regulations.

 

•  Batteries should never be thrown away or incinerated 

but disposed of in accordance with your local 

regulations concerning chemical wastes. 

TO AVOID THE HAZARDS OF ELECTRICAL 

SHOCK AND FIRE

 

• Do not handle the AC power cord with wet hands.

 

• Do not pull on the AC power cord when disconnecting it from an 

AC outlet. Grasp it by the plug.

 

• Do not put your 

fi

 ngers or objects into the unit.

LOCATION AND HANDLING

 

• Do not install the unit in direct sunlight or in a place subject to dust 

or strong vibration.

 

• Avoid a place with drastic temperature changes.

 

•  Install the unit in a horizontal and stable position. Do not place 

anything directly on top or bottom of the unit. Depending on your 

external devices, noise or disturbance of the picture and / or sound 

may be generated if the unit is placed too close to them. In this 

case, please ensure enough space between the external devices and 

the unit.

 

• Depending on the environment, the temperature of this unit may 

increase slightly. This is not a malfunction.

 

• Be sure to unplug the AC power cord from the AC outlet before 

moving or carrying the unit.

Trademark Information

 

• HDMI, the HDMI Logo, and High-De

fi

 nition Multimedia Interface 

are trademarks or registered trademarks of HDMI Licensing LLC in 

the United States and other countries.

 

• Manufactured under license from Dolby Laboratories. Dolby and 

the double-D symbol are trademarks of Dolby Laboratories.

 

• ENERGY STAR

®

 is a joint program of the U.S. Environmental 

Protection Agency and the U.S. Department of Energy helping us all 

save money and protect the environment through energy ef

fi

 cient 

products and practices.

Consumer Notice:

This TV has been set to maximize energy ef

fi

 ciency while delivering 

the best possible picture using the factory installed home mode 

settings.

Changing or enabling other features in this TV (e.g. brightened 

backlighting) will possibly increase energy consumption beyond the 

original ENERGY STAR

®

 quali

fi

 ed limits.

 

• The American Academy of Pediatrics discourages television viewing 

for children younger than two years of age.

 

Summary of Contents for LC220SS2


































Reviews: