Swisson XSP User Manual Download Page 22

Technical Data

Mains Voltage 

100 - 240 [VAC]

Main Frequency 

50/60 [Hz]

Current Consumption
Single Units 

0.2 [A]

Current Consumption
Double Units 

0.4 [A]

Operating Temperature 

0°F to 131°F (-17

C to 55

C)

Protocol Standard 

ANSI E1.11 (DMX-512)

 

ANSI E1.20 (RDM)

Safety Standards 

EN60950-1

 

UL508

 
EMC emission 

EN55103-1

EMC immunity 

EN55103-2

20 

No part of this documentation may be reproduced or transmitted in any form or by 
any means, electronically or mechanically, including photocopying and recording, 
without the prior written permission of SWISSON AG.
The information in this documentation is supplied without warranty of any kind, 
either directly or indirectly, and is subject to change without prior written notice. 
SWISSON AG, its employees or appointed representatives will not be held 
responsible for any damages to software, hardware, or data, arising as a direct or 
indirect result of operating and/or handling the product(s) mentioned herein.

Issued by

SWISSON AG 

SWISSON of AMERICA Corp.

Fabrikstrasse 21 

2419 East Harbor Blvd. #34

CH-3250 Lyss 

Ventura, CA 93001

Switzerland 

U.S.A.

e-mail: [email protected]

E

Summary of Contents for XSP























Reviews: