Swisher Logger LS67526S Owner'S Manual Download Page 5

5

TOWING SAFETY

• 

Do not allow persons to ride on splitter. Do not carry any cargo or wood on your
splitter. It may fall off and endanger vehicles that are following you.

• 

Be sure jack stand is in the travel position and coupling secure. This must also be
retracted so not to interfere while towing. Retract kickstand by removing pin,
rotating up, and replacing pin.

• 

Never exceed 45 MPH while towing your splitter. Be extra cautious when
traveling over rough terrain, especially over railroad tracks.

• 

Always be careful while backing your splitter. You could jackknife your log
splitter if not careful.

• 

Before using splitter, disconnect it from tow vehicle. A log could easily be
pushed forward into the vehicle.

• 

See tire and wheel specifications for PSI while towing.

• 

Be aware of the extra length of splitter while turning, parking, crossing
intersections, and in all driving situations.

• 

OPERATION INSTRUCTIONS

POSI-LOCK COUPLER

ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE. PLACE HANDLE IN LOCKED POSITION WITH BALL IN COUPLER.
TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT COUPLER IS NOT LOOSE ON BALL. CORRECT ADJUSTMENT WILL ALLOW
HANDLE TO BE RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE.

TO OPEN, PULL UP ON COUPLER HANDLE AND ROTATE FORWARD. PLACE COUPLER ON BALL WHEN BALL IS COMPLETELY
NESTED IN BALL SOCKET, ROTATE COUPLER HANDLE BACKWARD UNTIL HANDLE IS IN LOCKED POSITION.

AFTER TOWING FOR 50 MILES, CHECK COUPLER FOR TIGHTNESS ON BALL. ALWAYS CHECK TIGHTNESS BEFORE TOWING. BE
SURE COUPLER HANDLE IS IN LOCKED POSITION.

WARNING:

NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS. ALWAYS USE CORRECT BALL SIZE, MAKING SURE BALL
IS COMPLETELY INSERTED INTO COUPLER. LOCK COUPLER HANDLE SECURELY BEFORE TOWING. ALWAYS CHECK FOR
DAMAGES AND REPLACE IF DAMAGED. AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING.

OD16 – FUEL SHUT

OFF DECAL

OD07 – COLD WEATHER

DECAL

OD12 – HYDRAULIC FILL

PLUG DECAL

OD08 – OPERATOR INSTRUCTION DECAL

OD09 – DANGER/POSITION LOCK DECAL

SAFETY DECALS

Replace decals immediately if damaged.

Summary of Contents for Logger LS67526S













Reviews: