Swisher COMMERCIAL PRO Owner'S Manual Download Page 9

Ӆ

Operator Presence System:

Be sure to check that the operator presence and interlock systems are working properly before each use.  If your 
mower does not function as described, repair the problem immediately.

The engine should not start unless the parking brake is engaged and the PTO (Blade Engagement Switch)
is disengaged (pressed down). 

– See OPERATION FEATURES section of this manual.

When the engine is running and the brake is disengaged, the operator should never leave the seat without first
setting the parking brake and shutting off the engine. If the operator attempts to leave the seat without first setting
the brake, the engine should shut off. 
When the engine is running and the PTO switch is engaged, any attempt by the operator to leave the seat without
first disengaging the PTO switch, should shut off the engine.
The PTO switch should never engage without the operator on the seat.

Tires:

Maintain proper air pressure in all tires (SEE SPECIFICATIONS section).
Keep tires free of gasoline, oil or insect control chemicals which can harm rubber.
Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

Blade Maintenance:

For best results, mower blades must be kept sharp.  
Replace bent or damage blades.

Engage brakes & safely raise front of mower (SEE WARNING).
Hold or block blade from turning.
Loosen blade nut and remove blade.
Replace blade (SEE SPECIFICATIONS).

Battery:

To clean battery and terminals

Remove the BLACK terminal guard.
Disconnect the BLACK battery cable and locate it where it 

cannot come into contact with the battery. 

Remove the RED terminal guard.
Disconnect the RED battery cable and locate it where it 

cannot come into contact with the battery. 

Remove the battery.
Rinse the battery with plain water and dry.
Clean terminals and battery cable ends with wire brush 

until shiny.

Coat terminals with Dielectric Grease or Petroleum Jelly. 

(This helps seal and prevent corrosion.)

Reinstall battery.
Reconnect the battery cables. Attach the RED cable first

then the BLACK cable.

WARNING

When it is necessary to raise the mower 
for any repair or service, use jackstands 
to provide adequate support.  DO NOT 
rely on hydraulic or mechanical jacks.

CAUTION

Stop engine, apply brakes, and remove 
ignition key for safety. Disconnect spark 
plug wire.  Wear heavy, thick gloves when 
holding onto blade. Avoid the sharp edge 
of the blade.

CUSTOMER RESPONSIBILITIES

9

WARNING

The battery contains sulfuric acid and 
electrolytes which are poisonous and 
corrosive.

Summary of Contents for COMMERCIAL PRO

























Reviews: