Swisher COMMERCIAL PRO Owner'S Manual Download Page 16

Ӆ

Controls

Be familiar with all controls, their functions and how to operate them before starting the  

machine.

Motion control levers on each side of the console control the direction of movement.  

SEE FIGURE BELOW

Note: The pressure required to operate the mower is very slight.

Control Handles 

Neutral Position

Slow Forward

Fast Forward

OPERATION

90° Right Turn

90° Left Turn

Slow Reverse

360° Right Turn

360° Left Turn

NOTE:

If you have never used a 
Zero Turn mower before, 
refer to the Operation 
Controls section of this 
manual before attempting to 
operate one for the first time. 

16

Fuel Shut-Off Valves

Swisher Response Zero Turn Mowers are equipped with two shut-off valves, one for each tank.

These are located behind the seat and in front of the engine.

Only one tank should be used while operating the machine. When that tank runs empty or is close to

running empty, turn off that fuel shut-off valve and turn on the opposite shut-off valve. Operating  the
machine with both valves open could cause the system to pull air from an empty tank.

“ON” Position

(Parallel with fuel line)

“OFF” Position

(Perpendicular with fuel line)

Summary of Contents for COMMERCIAL PRO

























Reviews: