Swegon RX/HC Manual Download Page 3

We reserve the right to alter specifications.

GB.FUNKRXHC.180907

www.swegon.com   3

Size 040 - 080 (two compressors)

The refrigerant circuit contains a speed controlled com-
pressor and a compressor of the on/off type.

The speed controlled compressor works between a MIN 
level (total 12.5% per compressor, corresponding to 25% 
of the speed controlled compressor) and maximum speed. 

Increasing temperature requirement

At a temperature requirement below 12.5% the speed 
controlled compressor is run at 25% of max, speed. 

When the temperature requirement increases above 
12.5%, the speed controlled compressor is regulated to 
follow the temperature requirement. 

At a temperature requirement above 50%, the speed 
controlled compressor runs to max, speed. 

When the temperature requirement increases above 
62.5%, the on/off compressor and the speed controlled 
compressor are regulated to follow the temperature re-
quirement.  

At a temperature requirement of 100%, both compressors 
run at max, speed. 

Decreasing temperature requirement

When the temperature requirement decreases below 
100%, the on/off compressor is operational and the speed 
controlled compressor is regulated to follow the tempera-
ture requirement.

At a temperature requirement below 62.5% the speed 
controlled compressor is run at 25% of max, speed and 
the on/off compressor is operational.

When the temperature requirement decreases below 
50%, the on/off compressor shuts down and the speed 
controlled compressor is regulated to follow the tempera-
ture requirement.

At a temperature requirement below 12.5% the speed 
controlled compressor runs at 25% of max, speed.

Total output

The diagram shows the total capacity in per cent, which is 
the same as the control signal from the control system.

Compressor, on/off

Temperature requirement

Compressor operation

Compressor speed controlled

Temperature requirement

Compressor operation

Total output

Temperature requirement

Total output

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

60

 

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

60

 

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

0

20

 

 

100 % 

90

80

70

60

50

40

30

20

10

1

0  

40

60

80

100%

60

 

Temp. requirement, GOLD
Operation level, HC

Summary of Contents for RX/HC









Reviews: