background image

Actionair DWFX-C Installation Guide

14

Swegon reserves the right to alter specifications.           20220503 - LNNN00353 (5.0)                                                                               

Inspection and handover check sheet

This certificate applies only to Swegon Fire Dampers. The installer must complete this installation certificate when instal

-

ling fire and smoke dampers. A separate certificate must be completed for each individual fire and smoke damper.

Damper Unique System I.D: ..........................................................................................................................................................
Name of installation location:......................................................................................................................................................... 
Address:............................................................................................................................................................................................ 

Installation location identification section/floor/room: ................................................................................................................

 

Damper product type: .................................................................................................................................................................... 
Release fuse temperature: .............................................................................................................................................................. 
Notes/Considerations: ....................................................................................................................................................................
Installed by: ..................................................................................................................................................................................... 
Company Name: ............................................................................................................................................................................ 
Address: .......................................................................................................................................................................................... 
Company Telephone No: ............................................................................................................................................................... 
Installers Name: .............................................................................................................................................................................. 
Installers Telephone No: ................................................................................................................................................................. 
Date of installation: ........................................................................................................................................................................

It is hereby verified that the damper detailed above has been installed and tested according to the manufactures recom

-

mendations:
Installers signature: ................................................................................................ 

Date: ................................................

Question

Action

1

Are the dampers the correct type?

Confirm damper is correct type for the application

2

Are the dampers located correctly?

The damper location is to be checked against the installation 

drawings/details

3

Are the dampers correctly identified?

Unique system ID to be clearly indicated on the damper or 

other agreed location.

4

Have supports for both the damper and the adjacent 

ductwork been installed in accordance with the appro-

ved manner?

5

Are the dampers fitted in the correct orientation?

Confirm the damper is installed with any actuators (if applica

-

ble) on the left or right hand side. Not on the top or the bot-

tom (i.e. blade pivot running vertically) unless permitted under 

the respective DoP.

6

Is access through the ductwork, to the damper unob-

structed?

Unobstructed space should be provided for safe access to the 

damper. This must include access through ceiling voids and ad-

jacent services. Damper installer to advise the system designer 

if problems are foreseen.

7

Has the space around the damper and within the 

opening been left clear and not been used for other 

services?

Other services within the installation opening will invalidate 

the installation method. Damper installer to advise the lead 

contractor if problems are foreseen.

8

Using the access opening provided, check that blades 

open and close.

Check position of damper blades.

9

Has the damper been checked for internal cleanliness, 

free from damage and that vertical casings in particular 

are free from debris?

With the damper in the closed position, inspect for damage.

10

Has the damper been released to simulate operation of 

the thermal release? (Damper drop test)

Ensure damper operation is free from interference.

11

Have the damper blades been re-set following drop 

test and the access panel replaced?

After re-setting the damper, check the position shown on the 

blade position indicator is correct.

12

At the time of damper handover, is the fire barrier and 

penetration seal complete?

Damper installer to record on the handover register if  

any following trades are still to complete their activities.

13

Is the damper installation complete and available for 

handover prior to system commissioning?

Obtain the relevant acceptance of the damper installation from 

the CDM coordinator.

14

Is the completed handover register cross-referenced 

back to the identification codes listed in the system 

designers damper schedule?

Summary of Contents for actionair DWFX-C















Reviews:

Related manuals for actionair DWFX-C