background image

WARNING:  Continued 

Power Tool Hazard

To prevent personal injury or possible
death, always follow the electrical safety
recommendations of the power tool’s

manufacturer.  Do not use power tools in an unsafe
manner.  Power tools should only be connected to a circuit
protected by a ground-fault circuit interrupter (GFI).

Shock Hazard

Never use electric power tools around
water, condensation, or other liquids.
Electric shock can cause severe

burns, significant injuries, and even death.  If an
extension cord is required, always use an OSHA
approved extension cord.  Power cords should only be
connected to a circuit protected by a ground-fault circuit
interrupter (GFI).

Electrical Shock Hazard

Contacting l

ive electrical wiring with

power tools or hand tools can cause
serious injury or death.  Make sure all

related circuit breakers are turned OFF.  Test for live circuits
or wiring inside any wall where installation of the
Swanstone product requires cutting into a wall.

Electrocution Hazard

Water and other liquids conduct electric
current and can create a short circuit,
resulting in injury or death.  Keep all

liquids away from electrical cords and power tools.  DO
NOT create a short circuit between a source of electricity
and a liquid by being in contact with both simultaneously.

General Information

Required Tools

Circular saw with 60 to 80 tooth carbide blade

Sabre saw (straight up and down travel) with 
bi-metal blade (14 teeth per inch)

Drill with 3/8” drill bit

Hole saw for shower faucet/shower head

Tape measure

Masking tape (2” wide works best)

Level

Filler (thinset or mortar, if subfloor is not level)

Stud finder

Compass or dividers (scribe the panel to the wall)

Caulking gun

Required Tools (continued)

Clean paper towels or shop towels

2 x 4 lumber as required for bracing (see Bracing
Instructions)

Industrial grade, hot glue gun and glue sticks
(optional)

Kit Contents

Confirm that all parts of this kit have been included
before beginning installation.

BK-326072 Shower Wall Kit

(77-1/2 long x 64-3/4 wide x 4” thick; 196 lbs.)

2 — Sides (33-1/8 x 72”)

1 — Back (59 x 72”)

2 — Corner Trim Pieces (1-1/8 x 72”)

2 — Swanstone Soap Dishes

4 — Cartridges of clear silicone for back and side panels

1 — Tube of color matched 100% silicone sealant for

corners, corner moldings, and recessed shelf

1 — Tube of white silicone sealant for caulking around

the outer perimeter of shower

SS-29 Installation Kit

(13-3/4 long x 13-3/4 wide x 3-1/8” thick; 7 lbs.) 

4 — Cartridges of clear silicone sealant for back and

side panels

1 — Tube of color matched 100% silicone sealant for

corners, corner moldings, and recessed shelf

1 — Tube of white silicone sealant for caulking around

the outer perimeter of shower

SB-1248 Bench Seat Kit

(51-5/16 long x 14 wide x 1-9/16” thick; 16.5 lbs.)

1 — Seat Panel (12-3/4 x 48”)

RS-2215 Recessed Shampoo Shelf

(26-3/4 long x 19-1/2 wide x 6-3/4” thick; 13 lbs.)

1 — Shelf Unit

1 — Tube of color matched 100% silicone sealant

SS-3248 Shower Base Kit

(54 long x 38 wide x 10” thick; 49 lbs.)

1 — Base Unit

1 — Caulk Seal Gasket

1 — Strainer Plate

WARNING

The Swan Corporation – Swanstone

6

800-325-7008

Safety Guidelines

General Information

Summary of Contents for BK-326072

































Reviews: