3
Assembly Instructions
Before assembling or using the table-tennis table, please read the following instructions carefully. They contain impor-
tant information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions
in a safe place for maintenance purposes or for ordering spare parts.
All SVEN products are designed in accordance with the latest safety regulations and undergo a constant process of quality control dur-
ing manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our
customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you have
any cause for complaint, please contact your SVEN dealer.
GB
Note on Safety
■
The table-tennis table should be used only for its intended pur-
pose, i.e. for playing with suitable table-tennis bats and balls.
■
All other uses are prohibited and may be dangerous. The man-
ufacturer cannot be held liable for damage or injury caused by
improper use of the table.
■
Damaged or worn components may endanger your safety or
shorten the lifespan of the table-tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufactured
by SVEN.
■
The table-tennis table complies with all safety regulations. In-
correct repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the
safety of the user.
■
Instruct other persons (in particular children) using the table in
its correct use, and draw their attention to any potential source
of danger, especially when setting up or dismantling the table.
■
When setting up or dismantling the table, stay clear of its fold-
ing radius.
■
When folded up, the table-tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a shel-
tered position.
■
The table-tennis table may be pushed only into the transport po-
sition because there is otherwise a danger of injury.
■
The unit complies with the standard EN 14468–1:2004.
■
Depending on frequency of use, check all screws, bolts etc. reg-
ularly to ensure that they are in good condition.
■
In case of enquiry, please contact your SVEN dealer.
Handling the equipment
■
Do not use the table-tennis table until it has been fully and cor-
rectly assembled and checked.
■
Ensure that table-tennis tables which are not weatherproof are
not exposed to dampness or rain. Keep them well away from
direct sources of heat. Should the surface become warped, lay
the table on a level surface for a few days.
■
Set the table up on a level surface.
■
Do not cover it with plastic foil, under which condensation may
form. We recommend the weatherproof SVEN tarpaulin.
■
For practising without a partner, the table halves can be folded
up singly.
■
For more information on the sport of table-tennis, you are re-
ferred to the specialist literature on the subject.
■
Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the en-
vironment. In most cases, a slightly dampened cloth is sufficient.
■
Waste Disposal:
SVEN products are recyclable. At the end of its
useful life please dispose of this article correctly and safely (lo-
cal refuse sites).
Ersatzteilbestellung
Geben Sie bei Ersatzteilbestellungen bitte die vollständige Arti-
kelnummer, die Ersatzteilnummer, die benötigte Stückzahl sowie
die Seriennummer (siehe Ersatzteilzeichnung) an.
Bestellbeispiel:
Art.-Nr. 07166-900/Ersatzteil-Nr. 10100016/
Stück /Seriennummer: ........
Wichtig:
Zu verschraubende Ersatzteile werden grundsätzlich
ohne Verschraubungsmaterial berechnet und geliefert. Falls Be-
darf an entsprechendem Verschraubungsmaterial besteht, ist die-
ses durch den Zusatz
„mit Verschraubungsmaterial“
bei der Er-
satzteilbestellung anzugeben.
■
Bitte verschrauben Sie zunächst alle Teile lose und kontrollieren
Sie deren richtigen Sitz. Drehen Sie die selbstsichernden Mut-
tern bis zum spürbaren Widerstand zuerst mit der Hand auf,
anschließend ziehen Sie sie
gegen den Widerstand (Klemmsi-
cherung) mit einem Schraubenschlüssel richtig fest.
Kontrollieren
Sie alle Schraubverbindungen nach dem Montageschritt auf
festen Sitz.
Achtung:
wieder gelöste Sicherheitsmuttern werden
unbrauchbar (Zerstörung der Klemmsicherung) und sind durch
Neue zu ersetzen.
■
Aus fertigungstechnischen Gründen behalten wir uns die Vor-
montage von Bauteilen (z.B. Rohrstopfen) vor.
■
Bewahren Sie die Originalverpackung des Gerätes gut auf, da-
mit sie später u. U. als Transportverpackung verwendet werden
kann.
Wichtige Hinweise
D
