background image

Do move away the combustible around when weld the dooryard, ground and wall,.

The wire connection of base metal should be as close to the welding place as possible.

Never weld those facilities with gas pipe or airtight slot. 

Put fire extinguisher around the welding area to prevent fire. 

  The  gas   and   fumes  are  harmful   to   health,   please   wear   protective

device according to regulations.

Wear exhaust equipment and breathe preventive facilities to prevent gas poisoning or 
choke. 

Use suggested part exhaust equipment and breathe preventive facilities to prevent hurt or 
poisoning by gas and other powder, please. 

To prevent oxygen-deficiency, air out the gas-filled room which is full of CO

2

 and argon on 

the bottom, When operating on trunks, boilers, cabins, etc.  

Please accept the supervisor’s inspection when operating in narrow space. Air the room 
and wear breathe preventive facilities. 

Never operate in degrease, washing or spray space. 

Using breathe preventive facilities when weld shielded steel for it will cause poisonous dust
and gas. 

 

The arc, spark, residue and noise are harmful to health, please wear 

protective appliance. 

Eye protection against arc is recommended when welding or supervise welding. 

Please wear preventive spectacles. 

Welder’s gloves, welder’s goggles, long sleeve clothes, leather apron, and other standard
protection equipments must be worn for welding operation.

A screen to protect other people against the arc must be set in the welding place. 

 

Please follow the notes below to avoid gas cylinder toppling over or

broken.

Use the gas cylinder correctly. 

Use the equipped or recommended gaseous regulator. 

5

Summary of Contents for ARC 160-PFC






























Reviews: