Suzuki SWIFT RS415 2017 Service Manual Download Page 1123 | Manualshive

Page: 1123 / 1257

background image

Instrumentation / Driver Info. / Horn: 9C-16

Radio Assembly Removal and Installation

S4RS0A9306020

Removal

1) Disconnect negative (–) cable at battery.
2) Remove globe box referring to “Instrument Panel

Removal and Installation: ”.

3) Remove 2 mounting bolts (1).
4) Disconnect electrical connectors from radio

assembly.

5) Remove radio assembly (2) from instrument panel.

Installation

Reverse removal procedure.

Front Speaker Removal and Installation

S4RS0A9306021

Removal

1) Remove door trim referring to Step 1) to 3) of “Front

Door Glass Removal and Installation: in Section
9E”.

2) Remove 3 front speaker mounting screws (1).
3) Remove front speaker (2) from front door (3).
4) Disconnect front speaker coupler from front speaker

(2).

Installation

Reverse removal procedure.

Rear Speaker Removal and Installation

S4RS0A9306022

Removal

1) Remove door trim referring to Step 1) to 3) of “Rear

Door Glass Removal and Installation: in Section
9E”.

2) Remove 3 rear speaker mounting screws (1).
3) Remove rear speaker (2) from rear door (3).
4) Disconnect rear speaker coupler from rear speaker

(2).

Installation

Reverse removal procedure.

Horn Removal and Installation

S4RS0A9306027

Removal

1) Disconnect negative (–) cable at battery.
2) Remove front bumper referring to “Front Bumper

and Rear Bumper Components: in Section 9K”.

3) Disconnect horn connector (1).
4) Remove horn (2).

Installation

Reverse removal procedure for installation.

2

1

1

I4RS0A930026-

1

2

3

I4RS0A930027-

1

2

3

I4RS0A930027-

1

2

I4RS0A930028-

«
...
1121
1122
1123
1124
1125
...
»

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SWIFT RS415 2017

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

Brand: Yakima Pages: 11

Brand: Fabbri Pages: 4

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Axxess Pages: 8

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: Hyundai Pages: 19

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: Thule Pages: 12

Brand: Lexus Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands